Panasonic TX-P42ST60B / TX-P42ST60Y / TX-PR42ST60 (serv.man2) Service Manual ▷ View online
21
8 Disassembly and Assembly Instructions
8.1.
Disassembly Flow Chart for the Unit
This is a disassembly chart.
When assembling, perform this chart conversely.
When assembling, perform this chart conversely.
22
8.2.
Disassembly Procedure for the Unit
8.2.1.
Remove the Pedestal stand
1. Remove the Plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
downward.
by a soft cloth) with the Plasma panel surface facing
downward.
2. Remove the screws (
×4 )
3. Slide the Pedestal stand to the downside and remove the
Pedestal stand.
8.2.2.
Remove the Bottom cover
1. Remove the screws (
×4
) and remove the Bottom
cover.
8.2.3.
Remove the AC cord clamper B
1. Remove the screws (
×2
) and remove the AC cord
clamper B.
8.2.4.
Remove the Wi-Fi module
1. Remove the screw (
×1
) and remove the Wi-Fi
module.
8.2.5.
Remove the Bluetooth module
1. Remove the screw (
×1
) and remove the Dongle
cover.
2. Remove the Pin guides (
×2
) and disconnect the BT
connector.
3. Remove the Bluetooth module.
8.2.6.
Remove the Rear cover
1. Remove the screws (
×23
,
×2 ).
2. Remove the M8 caps (
×4 ).
3. Remove the Rear cover.
23
8.2.7.
Remove the P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
discharge from electrolysis capacitors.
1. Unlock the hooks and the tapes to free the cables
2. Disconnect the connectors (P2, P6, P11 and P35).
3. Remove the screws (
2. Disconnect the connectors (P2, P6, P11 and P35).
3. Remove the screws (
×5 ,
×1 ,
×1
) and remove
the P-Board.
8.2.8.
Remove the A-Board
1. Unlock the hooks and the tapes to free the cables.
2. Remove the screw (
2. Remove the screw (
×1
) and remove the M8 nut metal.
3. Disconnect the connectors (A1, A6 and A12).
4. Disconnect the USB cable (JK8605).
5. Disconnect the flexible cables (A20, A31, A32 and A33).
6. Remove the screws (
4. Disconnect the USB cable (JK8605).
5. Disconnect the flexible cables (A20, A31, A32 and A33).
6. Remove the screws (
×3 ).
7. Remove the Side shield metal and the Bottom shield
metal.
8. Remove the A-Board.
9. Remove the screws (
×2 ).
10. Remove the Heatsink (bottom) and the Heat rubber.
8.2.9.
Remove the Control unit assy
1. Disconnect the connector (C14).
2. Remove the claws (
2. Remove the claws (
×2
) and remove the Control unit
assy.
8.2.10. Remove the Speaker SQs
1. Unlock the hooks and the tapes to free the cables.
2. Disconnect the Relay connector.
3. Remove the screws (
2. Disconnect the Relay connector.
3. Remove the screws (
×2
each) and remove the
Speaker SQs (L, R).
24
8.2.11. Remove the Woofer
1. Unlock the hooks and the tapes to free the cables.
2. Disconnect the Relay connector.
3. Remove the screws (
2. Disconnect the Relay connector.
3. Remove the screws (
×3
) and remove the Woofer.
8.2.12. Remove the SN-Board
1. Unlock the tapes to free the cables.
2. Disconnect the flexible cables (SN21, SN22, SN23, SN24
2. Disconnect the flexible cables (SN21, SN22, SN23, SN24
SN25, SN26, SN27 and SN28) connected to the SN-
Board.
Board.
3. Disconnect the connector (SN2).
4. Disconnect the flexible cable (SN20).
5. Remove the screws (
4. Disconnect the flexible cable (SN20).
5. Remove the screws (
×8
) and remove the SC-Board.
8.2.13. Remove the SS-Board
1. Disconnect the connector (SS11).
2. Disconnect the flexible cable (SS33).
3. Disconnect the flexible cable (SS52).
4. Remove the screws (
2. Disconnect the flexible cable (SS33).
3. Disconnect the flexible cable (SS52).
4. Remove the screws (
×5 ,
×3
) and remove the SS-
Board.
8.2.14. Remove the SS2-Board
1. Disconnect the flexible cables (SS64 and SS67).
2. Remove the screws (
2. Remove the screws (
×2
) and remove the SS2-Board.
8.2.15. Remove the USB cable (A-WiFi)
1. Remove the screw (
×1 ).
2. Remove the USB cable (A-WiFi).
Click on the first or last page to see other TX-P42ST60B / TX-P42ST60Y / TX-PR42ST60 (serv.man2) service manuals if exist.