DOWNLOAD Panasonic TH-50PD12R Service Manual ↓ Size: 15.33 MB | Pages: 127 in PDF or view online for FREE

29

TH-50PD12R

1. Set Aging pattern (white pattern signal) by IIC mode.
2. Set the picture controls as follows.

Picture menu: Standard
Picture: +25
Aspect: Full

3. Connect Oscilloscope to TPSC1 and adjust VR16601 for 210V ± 10V.

1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.

Adjust the following voltages with the multimeter.

*See the Panel Label.
Caution

Absolutely do not reduce Vsus voltage below Ve not to damage the P.C.B.

Test Point

Volume

Level

TPSC1 (SC)

VR16601 (SC)

210V ± 10V
at 100 

µs

period on the down slope.

P.C.B.

Name

Test Point

Voltage

Volume

Remarks

P Board

Vsus

TPVSUS (SS)

Vsus ± 2V

R737 (P)

*

SC Board

Vad

TPVAD (SC)

-180V ± 2V

VR16600 (SC)

Vscn

TPVSCN (SC)

Vad_base:+145V±4V
GND_base: -35V±6V

Fixed

Vset

TPVSET (SC)

290V ± 9V

Fixed

SS Board

Ve

TPVE (SS)

Ve ± 2.5V

Fixed

*

Vda

TPVDA (P)

60V +1V ,  -2V

Fixed

D, A Board

White balance and Sub brightness for NTSC, PAL, HD, PC and 625i signals

A Board

Set Market Select Number to correct destination by MS mode (See chap. 6.1.4)

30

TH-50PD12R

31

TH-50PD12R

Instrument Name

Connect to

Setting

• RGB VGA60 W / B pattern
• Color analyzer

(Minolta CA-100 or equivalent)

PC input
Panel surface

User setting: Normal
(Picture menu: STANDARD)

Steps

Remarks

[Condition]

• Make sure the front panel to be used on the final set is fitted. 
• Make sure a color signal is not being shown before adjustment.
• Put the color analyzer where there is little color variation.

[Adjustment]

1. Set COMPONET / RGB-IN SELECT to RGB.
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (Hi)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature 

COOL (Hi)” in the below table.

7. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
8. Set color temperature to “NORMAL (Mid)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes 

the “Color temperature NORMAL (Mid)” in the below table.

10. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.

11. Set color temperature to “WARM (Low)”.

12. Set G drive to E0h and adjust B drive and R drive so the highlight window’s x, y become 

the “Color temperature WARM (Low)” shown in the below table.

13. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.

Adjustment target
Hi-light: x ± 0.003 y ± 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.

Picture Menu: Standard
User setting: Normal
Aspect: Full (16 : 9)
Position and size: Normal

• “7” key : color temperature select.
• “9” key : Picture menu select.

• Highlight section Signal amplitude 75%

• Drive standard G: E0h

32

TH-50PD12R