Panasonic TH-37PV80PA / TH-37PX80BA / TH-37PX80EA / TH-42PV80PA / TH-42PX80BA / TH-42PX80EA Service Manual ▷ View online
21
7.10. Remove the SS-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the connectors (SS11, SS12, SS23 and
2. Disconnect the connectors (SS11, SS12, SS23 and
SS34).
3. Disconnect the flexible cables (SS53A and SS56A) (42
inch)/(SS53 and SS56) (37 inch).
4. Remove the molding prop (
×1 ).
5. Remove the screws (
×5
) and remove the SS-Board.
7.11. Remove the stand brackets
1. Remove the plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered)
with the plasma panel surface facing downward.
with the plasma panel surface facing downward.
2. Remove the stand brackets (left, right) fastening screws
(
×4
each) and remove the stand brackets (left, right).
7.12. Remove the C1-Board
1. Remove the tuner unit. (See section 7.4.)
2. Unlock the cable clampers to free the cable.
3. Remove the flexible cables holder fastening screws (
2. Unlock the cable clampers to free the cable.
3. Remove the flexible cables holder fastening screws (
×8
).
4. Disconnect the flexible cables (CB1, CB2, CB3 and CB4).
5. Disconnect the flexible cables (C10 and C11).
6. Remove the screws (
5. Disconnect the flexible cables (C10 and C11).
6. Remove the screws (
×4
) and remove the C1-Board.
42 inch
37 inch
22
7.13. Remove the C2-Board
1. Remove the tuner unit. (See section 7.4.)
2. Unlock the cable clampers to free the cable.
3. Remove the flexible cables holder fastening screws
2. Unlock the cable clampers to free the cable.
3. Remove the flexible cables holder fastening screws
(
×8 ).
4. Disconnect the flexible cables (CB5, CB6, CB7 and CB8).
5. Disconnect the flexible cables (C20 and C21).
6. Disconnect the connector (C23).
7. Remove the screws (
5. Disconnect the flexible cables (C20 and C21).
6. Disconnect the connector (C23).
7. Remove the screws (
×4
) and remove the C2-Board.
42 inch
37 inch
7.14. Remove the front bracket
1. Disconnect the connector (A51 and A52). (See section
7.4.)
2. Remove the screws (
×4
) and remove the front
bracket.
7.15. Remove the G-Board and
GS-Board
1. Remove the front bracket. (See section 7.14.)
2. Remove the screws (
2. Remove the screws (
×2
) and remove the front shield
front.
3. Remove the screws (
×5
) and disconnect the connec-
tor (G51 and GS52).
4. Remove the G-Board and GS-Board.
7.16. Remove the speaker L, R
1. Disconnect the connector (A12). (See section 7.4.)
2. Remove the screws (
2. Remove the screws (
×4
each) and remove the
speaker L, R.
23
7.17. Remove the S-Board
1. Remove the stand brackets. (See section 7.11.)
2. Remove the screws (
2. Remove the screws (
×2 ).
3. Disconnect the connector (S1).
4. Remove the screws (
×2
) and remove the S-Board.
7.18. Remove the K-Board
1. Remove the S-Board. (See section 7.17.)
2. Unlock the cable clampers to free the cable.
3. Remove the screws (
2. Unlock the cable clampers to free the cable.
3. Remove the screws (
×2 ).
4. Disconnect the connectors (K1) and remove the K-Board.
7.19. Remove the Plasma panel sec-
tion from the Cabinet assy
(glass)
(glass)
1. Remove the stand brackets (left, right) fastening screw
(
×1
each).
2. Remove the cabinet assy and the plasma panel fastening
screws (
×7 ).
24
3. For leaving the plasma panel from the front frame, pull the
bottom of the cabinet assy forward, lift, and remove.
4. Remove the spacers and spacer rings (
×6 ).
Caution:
• Please confirm the installation plate of Spacer and Spacer
Ring when you exchange the Plasma Panel, and install
Spacer and Spacer Ring in an original installation place after
exchange the Plasma Panel.
Spacer and Spacer Ring in an original installation place after
exchange the Plasma Panel.
7.20. Replace the plasma panel
(finished)
1. Place the new plasma panel (finished) on the flat surface
of the table (covered by a soft cloth), with the plasma
panel surface facing downward.
panel surface facing downward.
2. Attach the C1-Board and the C2-Board, connect the flexi-
ble cables (
×16) from the Plasma panel to the C1-Board
and the C2-Board, and fit the flexible cable holders.
3. Attach the Hooks (left, right) and fit the stand brackets (L,
R) to the new plasma panel.
4. Place the plasma panel section on the servicing stand.
5. Attach the cabinet assy and each P.C.Board and so on, to
5. Attach the cabinet assy and each P.C.Board and so on, to
the new plasma panel.
*When fitting the cabinet assy, be careful not to allow
*When fitting the cabinet assy, be careful not to allow
any debris, dust or handling residue to remain
between the front glass and plasma panel.
Click on the first or last page to see other TH-37PV80PA / TH-37PX80BA / TH-37PX80EA / TH-42PV80PA / TH-42PX80BA / TH-42PX80EA service manuals if exist.