DOWNLOAD Panasonic TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E Service Manual ↓ Size: 31.53 MB | Pages: 127 in PDF or view online for FREE

Model
TH-37PR10B TH-37PR10E TH-42PR10B TH-42PR10E
Pages
127
Size
31.53 MB
Type
PDF
Document
Service Manual
Brand
Device
Plasma / GPH10D CHASSIS
File
th-37pr10b-th-37pr10e-th-42pr10b-th-42pr10e.pdf
Date

Panasonic TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E Service Manual ▷ View online

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
  · Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
  · Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
  · After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
7
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
5 Service Hint
Note:
  · The remote control transmitter is not included with this set.
  · Execute by the following remote control transmitter when repairing.
product number : EUR7636070R
Board Name
Function
Board Name
Function
DN
Digital Signal Processor, Microcomputer
C1
Data Drive (Right)
D
Digital Signal Processor
Format Converter, Plasma AI Processor
C2
Data Drive (Left)
SP
Speaker
DS
Slot Interface (Audio / Video / Sync input Switch),
SYNC Processor, Audio Processor,
Speaker Out Amplifier, DC-DC Converter
S
Power switch
K
Remote receiver, LED_G,R
SS
Sustain drive
GK
Key switch
SC
Scan drive
P
Power supply
SU
Scan out (Upper)
HX
PC / RS-232C_Input terminal
SD
Scan out (Lower)
Note:
  · Extension cable kit Slot Board is supplied as service fixtures and tools.
(Parts No. TZSC0704)
8
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
6 Disassembly
TH-37PR10B/E
  · To disassemble P.C.B., wait for 1 minute after power was
off for discharge from electrolysis capacitors.
  ·  and
marks indicate screw positions.
6.1. Removal of Rear Cover
 1. Remove screws (×6
, ×6
, ×14
, ×8
) and then
remove the Rear Cover.
6.2. Removal of Slot Block
 1. Disconnect the connectors (DS1, DS4, DS6, DS7).
 2. Remove 4 screws and then remove the Slot Block.
 3. Disconnect the connectors(DS2, DS8, DS15).
6.3. Removal of DS-Board
 1. Remove the Slot Block.
(Refer to Removal of Slot Block)
 2. Disconnect the connector(DS14).
 3. The Slot Block is turned inside out.
 4. Remove 6 screws and then remove the Slot Cover.
 5. Remove 6 screws and then remove DS-Board.
9
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
6.4. Removal of HX-Board
 1. Remove the Slot Block.
(Refer to Removal of Slot Block)
 2. Remove DS-Board.
(Refer to Removal of DS-Board)
 3. Remove 2 screws and then remove the Slot Case.
 4. Remove 4 Hexagonal-Head screws and 2 screws and then
remove HX-Board.
6.5. Removal of Speaker(L, R)
 1. Connected terminal hook is pushed, and the speaker lead
in 4 places is pulled out.
 2. Remove 8 screws and then remove the Speaker(L, R).
6.6. Removal of DN-Board
 1. Disconnect the connector(DN6).
 2. Remove the Flexible Cable from the connector(DN1).
 3. Remove 4 screws and then remove DN-Board and the
Fixed Plate.
Note:
A re-setup of the destination is performed by MS mode
after DN-Board exchange.
10
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
Page of 127
Display

Click on the first or last page to see other TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E service manuals if exist.