DOWNLOAD Panasonic TH-103PF12E Service Manual ↓ Size: 5.84 MB | Pages: 94 in PDF or view online for FREE

Model
TH-103PF12E
Pages
94
Size
5.84 MB
Type
PDF
Document
Service Manual
Brand
Device
Plasma / GPH12D CHASSIS
File
th-103pf12e.pdf
Date

Panasonic TH-103PF12E Service Manual ▷ View online

8
TH-103PF12E
3.2.
Applicable signals
9
TH-103PF12E
4 Specifications
Power Source
220-240 V AC, 50/60Hz
Power Consumption
Power on
1450 W
Stand-by condition
Save OFF 1.2 W, Save ON 0.7 W
Power off condition
0.4 W
Plasma Display panel
Drive method: AC type 103-inch,
16:9 aspect ratio
Screen size
2,269 mm (W) 
× 1,276 mm (H) × 2,603 mm (diagonal)
(No. of pixels)
2,073,600 (1,920 (W) 
× 1,080 (H))   [5,760 × 1,080 dots]
Operating condition
Temperature
°C - 40 °C
Humidity
20 % - 80 %
Applicable signals
Scanning format
525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) / 
60i 60p 50i 50p 24p 25p 30p 24sF, 1250 (1080) / 50i
PC signals
VGA, SVGA, XGA, SXGA
UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
DVI-D IN
Video Input
DVI-D  24 Pin 
× 1
compliance with DVI Revision 1.0
Audio Input
Stereo mini jack (M3) 
× 1
0.5 Vrms
Content Protection
Compatible with HDCP 1.1
LAN
RJ45 10BASE-T / 100BASE-TX, compatible with PJLink
TM
COMPONENT / RGB IN
Y / G (BNC)
with sync 1.0 Vp-p (75-ohm)
P
B
/B (BNC), P
R
/R (BNC)
0.7 Vp-p (75-ohm)
Audio Input
Stereo mini jack (M3) 
× 1
0.5 Vrms
PC IN
(HIGH-DENSITY Mini-D-SUB 15PIN)
Y or G with sync 1.0 Vp-p (75-ohm)
Y or G without sync 0.7 Vp-p (75-ohm)
B / P
B
 / C
B
: 0.7 Vp-p (75-ohm)
R / P
R
 / C
R
: 0.7 Vp-p (75-ohm)
HD / VD: 1.0 - 5.0 Vp-p (high impedance)
VBS (use HD port)
with picture 1.0 Vp-p  (high impedance)
without picture 0.3 Vp-p  (high impedance)
Audio Input
Stereo mini jack (M3) 
× 1
0.5 Vrms
SERIAL
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) 
RS-232C COMPATIBLE
AUDIO OUT
RCA PIN JACK 
× 2 (L / R)
OUTPUT LEVEL : VARIABLE (-
 -  0 dB)
[INPUT 1KHz / 0dB, 10Kohm Load]
Accessories Supplied
Remote Control Transmit-
ter
EUR7636090R
Batteries
R6 Size 
× 2
Fixing band
TMME203 
× 2
Ferrite core
J0KG00000146 (Set of 2)
Noise cut filter
TXZDM011MBE
Dimensions (W 
× H × D)
2,412 mm 
× 1,419 mm × 129 mm (141 mm when including protruding portion of slots) 
Mass (weight)
approx. 201.0 kg net
Note:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-2, EN61000-3-3.
10
TH-103PF12E
5 Operating Instructions
11
TH-103PF12E
GPF12D chassis series have special function and operation setting facility called Option Menu. This Option Menu is useful 
for special function required customers. This should be set at the installation stage.
Note:
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote ID”
adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the “Volume down” button on main unit together with “R” button on the remote control and hold for more than 5 seconds.
The “SHIPPING“ menu is displayed and the lock is released when it disappears.
Option Menu for GPF12D series
Option menus
default setting
Contents
Weekly Command Timer
---
Sets Weekly Command Timer.
Onscreen display
On
Enable/Disable to display input mode indication after power on and no signal 
indication.
Initial INPUT
Off
Sets the initial input mode when the power is turned on. Allow input mode selec-
tion while power is on.
Initial VOL level
Off
Sets the initial volume level when the power is turned on. Allow Volume control 
while power is on.
Maximum VOL Level
Off
Sets the maximum volume to desired level. Volume cannot exceed this level.
INPUT lock
Off
Fixes the input mode to AV, Component/RGB or PC. Can not change input 
mode by input selection key.
Button lock
Off
Enable/Disable bottom operation buttons (Input, Menu, Enter and/or volume up/
down)
Remocon User Level
Off
Remote key invalidation.
Off: Valid key is all key of remote.
User1: Valid key are only Stand-by (ON/OFF), Input, Direct input, Picture, Sur-
round, Sound mute On/Off, and volume adjustment.
User2: Valid key is only Stand-by (ON/OFF).
User3: All keys are null and void
Off-timer function
Enable
Off-timer operation Enable/Disable.
Initial Power Mode
Normal
Sets the power mode of the unit for when the power recovers from failure or 
after plugging off and in again.
ID select
0
Set ID number from 0 to 100.
Remote ID
Off
Remote ID function On/Off.
(While the Remote ID on, standard remote function can not control the unit.)
Serial ID
Off
Serial ID function On/Off
Display size
Off
Display size function On/Off
Studio W/B
Off
Studio W/B function On/Off
Studio Gain
Off
Studio Gain function On/Off
Slot power
Off
Sets the slot power mode while the power is turned on.
Allow Optional Terminal Board insert Slots while power is on.
Power On Screen Delay
Off
You can set the power-on delay time of the displays to reduce the power load, 
when you press 
 to turn on the multiple displays that are set together, for 
example, on MULTI DISPLAY system.
Set each display’s setting individually.
Clock Display
Off
Clock Display function On/Off.
All Aspect
Default
Aspect mode: default/All aspect mode.
Auto Setup
Manual
Sets the operational mode of the automatic position adjustment in the POS./
SIZE memu. 
Rotate
Off
Rotate function On/Off
Serial Slot Select
Slot1
Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fixed serial 
terminal.
Page of 94
Display

Click on the first or last page to see other TH-103PF12E service manuals if exist.