Panasonic CF-R1P82ZVGH Service Manual ▷ View online
21
4.4.3. Diagnosis by Error Code
Error code
Message
Error Description
Possible faulty part
0200
Failure Fixed Disk
Fixed disk in not working or not configured properly.
HDD
Run the Setup Utility and check that the hard disk
Main board
capacity is displayed at [Primary Master].
If the [None] is displayed, disk error is occurred.
If the [None] is displayed, disk error is occurred.
0211
Keyboard error
Keyboard not working. Confirm the keyboard is connected
Keyboard
to the computer and that a key is not being held down.
0212
Keyboard Controller Failed Keyboard controller failed test.
Main board
May require replacing keyboard controller.
0230
System RAM Failure
System RAM failure at offset
nnnn of the 64k block at
Main board
at offset :
nnnn
which the error was detected. If you installed RAM module,
remove the RAM module and reinstall it.
remove the RAM module and reinstall it.
0231
Shadow RAM Failure
Shadow RAM failure at offset
nnnn of the 64k block at
Main board
at offset :
nnnn
which the error was detected. If you installed RAM module,
remove the RAM module and reinstall it.
remove the RAM module and reinstall it.
0232
Extended RAM Failure
Extended memory not working or not configured properly
Main board
at offset :
nnnn
at offset
nnnn.
Extension memory
0250
No battery on the system
CMOS backup battery exhausted.
Lithium battery
Battery replacement is required.
0251
System CMOS checksum
System CMOS has been corrupted or modified incorrectly, Incorrect Setup
bad
perhaps by an application program that changes data
Lithium battery
-Default configuration used stored in CMOS.
The BIOS installed Default SETUP Values. If you do not
want these values, enter Setup and enter your own values.
If the error persists, check the system battery or contact
Panasonic.
want these values, enter Setup and enter your own values.
If the error persists, check the system battery or contact
Panasonic.
0260
System timer error
The timer test failed. Requires repair of system board.
Main board
0270
Real time clock error
Real-time clock fails BIOS test. May require board repair.
Main board
0271
Check date and time
Incorrect date and time on the system.
Incorrect Setup
settings
Set the correct date and time using the setup utility.
0280
Previous boot incomplete
Previous POST did not complete successfully.
Boot-up failure
-Default configuration used POST loads default values and offers to run Setup.
If the failure was caused by incorrect values and not
corrected, the next boot will likely fail.
corrected, the next boot will likely fail.
02D0
System cache error
CPU trouble.
Main board
-Cache disabled
02F5
DMA Test Failed
Server BIOS2 test error: Cannot write to extended DMA
Main board
(Direct Memory Access) registers.
22
5 Self Diagnosis Test
1. Floppy disk is included for the self-diagnostic tests that should be performed before using this product.
2. Connect External Floppy Disk Drive (FDD) to USB port for diagnosis test.
Important notice
System password
This product has a password function. If this function is turned on, the self-diagnostics tests will not work.
You will need to ask the user for the password before performing the self-diagnostics.
5.1. Outline of Self Diagnostic Tests
23
5.1.1. List of main test items
The section item displays the items selected under Automatic test. If you select Automatic test, these test items will be
performed automatically. You can use Selection test to choose items from the menu screen that you want have tested.
These items are shown below.
5.2. Automatic Test
Test execution
From the menu screen shown below, be sure to choose DIAG on FD (CF-R1) and press Enter.
menu screen
24
Speaker test, VESA test
The speaker test involves listening to music and choosing OK or Not okay. The VESA test involves looking at the display to see
if it is satisfactory then choosing OK or Not okay.
Diagnostic result
If no errors occur: The screen shows the word “Pass” in large letters.
If errors occur: The test stopped when an error occurs and the error message is displayed.
For explanations of error messages, see Error Message and Problem Categories.
Quitting the test
At the screen shown below, simultaneously press the ALT and X keys.
Input screen
5.3. Peripheral Test
Test execution
From the menu screen shown below, be sure to choose the follwing items and press Enter.
2. SPEED STEP test
3. LAN test
4. SD Card I/F test
menu screen
SPEED STEP test
This tests the changing performance of CPU. Choose SPEED STEP test and press Enter.
LAN test
This test checks for internal LAN device. Choose LAN test and press Enter.
SD Card I/F test
This tests the SD Card I/F functions. Choose SD Card I/F test and press Enter.
Click on the first or last page to see other CF-R1P82ZVGH service manuals if exist.