Panasonic CF-R1 Service Manual ▷ View online
30
6.2.5. Removing the HDD
Preparation: perform the section 6.2.1. to 6.2.3. first.
1. Pull off the pad heat spleader.
2. Remove the HDD FPC ass’y from the connector (CN14).
1. Pull off the pad heat spleader.
2. Remove the HDD FPC ass’y from the connector (CN14).
3. Remove the HDD damper.
4. Remove the HDD FPC ass’y
4. Remove the HDD FPC ass’y
6.2.6. Removing the main board
Preparation: perform the section 6.2.1. to 6.2.5. first.
1. Remove the 2 screws (G).
1. Remove the 2 screws (G).
Screw (G): DFHE5025XA
2. Remove the FFC from the connector (CN13), and then
remove the PCMCIA slot.
3. Remove the jack ESD sheet, pad heat spleader and RJ dust
cover.
4. Tear off the kapton tape, and then remove the main board.
31
6.2.7. Removing the flat pad
Preparation: perform the section 6.2.1. to 6.2.3. first.
1. Remove the 2 screws (H), and then remove the pad cabinet.
1. Remove the 2 screws (H), and then remove the pad cabinet.
Screw (H): DXHM0040ZA
2. Remove the touch pad from the pad cabinet.
3. Remove the FFC (PAD).
3. Remove the FFC (PAD).
6.2.8. Removing the edge cover
Preparation: perform the section 6.2.1 first.
1. Remove the 6 screws (I), and then remove the edge covers
1. Remove the 6 screws (I), and then remove the edge covers
(L) and (R).
Screw (I): DFHE5025XA
Screw (I): DFHE5025XA
6.2.9. Removing the hinge
Preparation: perform the section 6.2.1. to 6.2.4. and 6.2.8. first.
1. Remove the 4 screws (J), and then remove the hinges (L)
1. Remove the 4 screws (J), and then remove the hinges (L)
and (R).
Screw (J): DXQT26+D4FZL
Screw (J): DXQT26+D4FZL
6.2.10. Removing the LCD front ass’y
Preparation: perform the section 6.2.1. to 6.2.4. , 6.2.8. and 6.2.9.
first.
1. Remove the 9 latches, and then remove the LCD front ass’y.
first.
1. Remove the 9 latches, and then remove the LCD front ass’y.
32
6.2.11. Removing the LCD unit
Preparation: perform the section 6.2.1. to 6.2.4. , and 6.2.8. to
6.2.10. first.
1. Lift the LCD upward, and then lay aside after turn over.
2. Remove the LCD cable from the LCD unit.
3. Remove the back light cable from the inverter board, and then
6.2.10. first.
1. Lift the LCD upward, and then lay aside after turn over.
2. Remove the LCD cable from the LCD unit.
3. Remove the back light cable from the inverter board, and then
remove the LCD unit.
6.2.12. Removing the inverter board
Preparation: perform the section 6.2.1. to 6.2.4. , and 6.2.8. to
6.2.11. first.
1. Remove the back light cable and LCD cable from the inverter
6.2.11. first.
1. Remove the back light cable and LCD cable from the inverter
board.
2. Tear off the kapton tape, and then remove the inverter board.
6.2.13. Removing the inverter board
Preparation: perform the section 6.2.1. to 6.2.4. , and 6.2.8. to
6.2.11. first.
1. Remove the wiring of back light cable from the LCD cable
6.2.11. first.
1. Remove the wiring of back light cable from the LCD cable
sheet, and then remove the LCD cable sheet.
2. Tear off the reflector tape, and then remove the back light.
Click on the first or last page to see other CF-R1 service manuals if exist.