Panasonic CF-19CHBAXBM Service Manual ▷ View online
9-20
n
Assembly of Display Unit
LCD UNIT
A
Note
Avoid any stress on the Cable.
Avoid any stress on the Cable.
Safety Working
Details of "A"
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Order of fixing
Close the LCD hooking the
Hinge on the Top Case, and
then fold back.
Hinge on the Top Case, and
then fold back.
Insert all of antenna cables
into the notch of the board.
into the notch of the board.
LCD Cable Insert Position
Set to the Top Case Assy
Black/White
Blue/Gray
Brown
Pass the Cable through
the groove.
Note: Running over
affects the waterproof
performance..
the groove.
Note: Running over
affects the waterproof
performance..
9-21
9.2.7.
Setting the Pad PCB and SW PCB
1. Attach both the SW PCB and the Operation Sheet to the
Cabinet.
2. Connect the 3 Cables to the 3 Connectors.
(CN800,CN805,CN807)
3. Fix the Pad PCB using the 4 Screws. <N1>
Note:
Tighten the Screws in the numbered order (No1 to
No4).
No4).
Screws <N1> : DFHE5025XA
SW PCB
Operation Sheet
<N1>:No.3
Pad PCB
Connector(CN807)
Connector(CN805)
<N1>:No.2
<N1>:No.1
<N1>:No.4
9-22
n
Assembly of the Pad PCB and SW PCB
n
Putting of the TP Bottom Tape
9.2.8.
Setting the left LED PCB and right LED PCB
1. Connect the Cable to the Connector. (CN806)
2. Fix the left LED PCB.
3. Connect the Cable to the Connector. (CN801)
4. Fix the right LED PCB.
5. Attach the two Release Papers.
6. Attach the Palm Rest Ass'y.
2. Fix the left LED PCB.
3. Connect the Cable to the Connector. (CN801)
4. Fix the right LED PCB.
5. Attach the two Release Papers.
6. Attach the Palm Rest Ass'y.
SW PCB Ass’y
Match the edge
and attach it.
and attach it.
Avoid coming off of the LED part,
or running over the LED part.
or running over the LED part.
No direction when inserting
(Note) Arrow without specified measurement: 0 to 0.5 mm
PAD PWB
SW FPC
LED(R) FPC
Power SW Cable
Operation
Sheet
Sheet
Operation Tape
Power Cable Cushion
Thermistor
SW PCB
Ensure that the direction
is right when attaching.
The Connector bracket is
on the back side.
is right when attaching.
The Connector bracket is
on the back side.
Insert
Insert
Insert
Insert
8 2mm
Back side
Wrap around the Cable.
PAD PWB ASSY
PAD MAIN FPC ASSY
PAD MAIN FPC Ass’y
0 1mm
0 1mm
PAD-Main FPC
Tape
Stiffening Plate Side
Fold back
Front side
SW PCB Ass’y
Screw
Screw
Match to the upper left corner. 0 to 0.5mm
Release Paper
Release Paper
left LED PCB
right LED PCB
Connector(CN801)
Connector(CN806)
9-23
n
Assembly of the left LED PCB and right LED PCB
9.2.9.
Setting the Power SW PCB
1. Connect the Cable to the Connector. (CN9)
2. Fix the Power SW PCB using the Screw. <N1>
2. Fix the Power SW PCB using the Screw. <N1>
Screws <N1> : DFHE5025XA
n
Assembly of the Power SW PCB
LED(L) PCB Ass’y
LED(R) PCB Ass’y
0 3mm
Back side
LED Light Guide Sheet(L)
LED PCB Tape(L)
LED PCB(L)
LED(L) FPC
LED Light Guide Sheet(R)
LED PCB(R)
LED PWB Tape(R)
Match the edge and attach it.
Match the edge and attach it.
Match the edge and attach it.
Avoid running over the LED.
Avoid running over the LED.
Match the edge and attach it.
Ensure it does not come over the end
of the Board by 0.5 mm or more.
Avoid coming over it.
Ensure it does not come over the end
of the Board by 0.5 mm or more.
Avoid coming over it.
<N1>
Connector(CN9)
Power SW
PCB
1
2
Power SW PCB
Power Spring Sheet
Spring
Screw
Attach
Insert
Insert the Cushion
between the ribs.
between the ribs.
Avoid coming over
Insert it to Knob and
Pin on the Top Case
Fold the board back and fix with screw.
(Note) Arrow without specified measurement: 0 to 0.5 mm
0 1mm
0 1mm
Safety Working
Click on the first or last page to see other CF-19CHBAXBM service manuals if exist.