Panasonic KX-NTV150NE Service Manual ▷ View online
8
KX-NTV150 Series
5 Installation Instructions
Installing the stand
Note
• Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or
operation inconsistent with this documentation.
A. When installing on a flat surface.
Note
• Use rubber to prevent stand from shifting if necessary. Rubbers should be aligned with the 4 arcs in the corner.
B. When installing on the wall
Note
Note
• Skid proof stickers should be aligned with the 4 arcs in the corner. Attach the camera to stand and orient the shooting angle.
If preferred, use the included screws to secure the camera stand to a mounting surface.
9
KX-NTV150 Series
6 Operating Instructions
KX-NTV150 and KX-NTV160 are designed for SIP communication, which can easily be compatible with existing SIP system, such
as Panasonic PBX with SIP protocol. Besides, users can access KX-NTV150/KX-NTV160 through WEB browser, and other soft-
ware.
as Panasonic PBX with SIP protocol. Besides, users can access KX-NTV150/KX-NTV160 through WEB browser, and other soft-
ware.
Softphone application
10
KX-NTV150 Series
7 Troubleshooting Guide
7.1.
No power supplied by PoE or AC Adaptor
7.2.
No image
1. Connect Ethernet cable with PoE or AC Adaptor to Main Board.
2. Turn the multimeter to DCV setting.
3. Measure the voltage between TP20_5V9V and TP14_GND.
4. Check if the value is DC+5V (+4.75V ~ +5.25V) in case of power
2. Turn the multimeter to DCV setting.
3. Measure the voltage between TP20_5V9V and TP14_GND.
4. Check if the value is DC+5V (+4.75V ~ +5.25V) in case of power
supplied by PoE, or check if the value isDC+9V (+8.1V ~ +9.9V)
in case of power supplied by AC Adaptor.
in case of power supplied by AC Adaptor.
5. Disconnect Ethernet cable with PoE or AC Adaptor.
Malfunction
Main Board exchange.
1. Check Main Board PCB’A (J1)Connect.
2. Check if Main Board PCB'A _U1 is damaged.
3. Check if Sensor board functions normally.
*U1-(SOC, VVTK8112, VATICS)
*J1-(PIN HEADER, T-DPH20SD2GT-C0, DISNT)
*J1-(PIN HEADER, T-DPH20SD2GT-C0, DISNT)
Malfunction
Main Board exchange at first.
If trouble is not closed yet, Sensor Board need to exchange too.
If trouble is not closed yet, Sensor Board need to exchange too.
J1
U1
11
KX-NTV150 Series
7.3.
No Audio
7.4.
Wrong date
7.5.
Fail connecting to cable LAN
1. Check if Main Board PCB'A _U26, U14 is damage.
*U26-(IC,FM1288-GE410,FORTEMEDIA)
*U14-(IC,TPA2011D1YFF,TI)
*U14-(IC,TPA2011D1YFF,TI)
Malfunction
Main Board exchange at first.
If trouble is not closed yet, Front cover Assy need to exchange too.
If trouble is not closed yet, Front cover Assy need to exchange too.
1. Check if Main BD PCB'A_ D19 is damaged.
2. Measuring if input voltage of BT2 is DC3.3V by multimeter.
*D19-(DIODE, BAT54C2-0-T5-G, CYSTEK)
*BT2-
(GCAP, 0.2F, 3.3V, -20~+80%, ELNA KL series)
*BT2-
(GCAP, 0.2F, 3.3V, -20~+80%, ELNA KL series)
Note:
BT2 pin: 260°C±5°C
soldering time: 2Sec±0.5Sec
soldering time: 2Sec±0.5Sec
Malfunction
Main Board exchange.
1. Check if Main Board PCB’A _U1, U6 is damaged.
*U1-(SOC, VVTK8112, VATICS)
*U6-(IC, KSZ8051MNL, MICREL)
*U6-(IC, KSZ8051MNL, MICREL)
Malfunction
Main Board exchange.
U26
U14
D19
BT2
U6
U1
Click on the first or last page to see other KX-NTV150NE service manuals if exist.