Panasonic UB-T880 / UB-T880W (serv.man5) Service Manual / Supplement ▷ View online
Order Number KM71302820SE
Category Number H19
Electronic Board (elite Panaboard)
Model No.
UB-T880
UB-T880W
UB-T880W
Subject : Complying with *ErP directive and others
TABLE OF CONTENTS
PAGE
1 TOPICS OF MAIN CHANGED CONTENTS---------------- 2
2 “SECTION 1 GENERAL PRECAUTIONS”----------------- 3
2 “SECTION 1 GENERAL PRECAUTIONS”----------------- 3
2.1. “Section 1.1 Before Using This Manual” ------------- 3
3 “SECTION 9 TROUBLESHOOTING”------------------------ 4
3.1. “Section 9.4 Others” -------------------------------------- 4
4 “SECTION 11 SCHEMATIC DIAGRAM”-------------------- 5
4.1. “Section 11.1 CONTROL Board” ---------------------- 6
5 “SECTION 12 CIRCUIT BOARDS” -------------------------14
5.1. “Section 12.1 CONTROL Board” ---------------------15
6 “SECTION 13 PARTS LOCATION AND MECHANI-
CAL PARTS LIST” -----------------------------------------------18
6.1. "Section 13.3 Board”-------------------------------------19
7 “SECTION 14 REPLACEMENT PARTS LIST” ----------20
7.1. "Section 14.1. CONTROL Board" --------------------21
Note1: * ErP
DIRECTIVE 2009/125/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 21 October 2009
establishing a framework for the setting of ecodesign requirements for energy-related products
DIRECTIVE 2009/125/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 21 October 2009
establishing a framework for the setting of ecodesign requirements for energy-related products
Note2:
Please file and use this manual together with the following service manual.
1. Original Service Manual for UB-T880 / T880W (Order No. KM71105670CE)
Please file and use this manual together with the following service manual.
1. Original Service Manual for UB-T880 / T880W (Order No. KM71105670CE)
2
1 TOPICS OF MAIN CHANGED CONTENTS
Remarks
Important level codes and Reason codes for the following changed contents
1. Important level codes
A: High
B: Middle
C: Low
2. Reason Codes
(1) Change Spec. (Product Number, Engineering change, and others)
(2) Add information on Products UB-T880 / T880W
(3) Correction
A: High
B: Middle
C: Low
2. Reason Codes
(1) Change Spec. (Product Number, Engineering change, and others)
(2) Add information on Products UB-T880 / T880W
(3) Correction
Section No.
(Original Service
Manual)
Contents
Reference Section
on this supplement
Remarks
1
Add the product version information
2. "SECTION 1 GENERAL
PRECAUTIONS"
PRECAUTIONS"
A-(1)
9
Add Automatic power-off function's issue complying
with ErP
with ErP
3. "SECTION 9
TROUBLESHOOTING"
TROUBLESHOOTING"
A-(1)
11
1. Add the Serial Number information to the original
schematic diagram for CONTROL Board
2. Add the schematic diagram for CONTROL Board
complying with ErP
schematic diagram for CONTROL Board
2. Add the schematic diagram for CONTROL Board
complying with ErP
4. "SECTION 11 SCHEMATIC
DIAGRAM"
DIAGRAM"
A-(1)
12
Add the circuit boards for CONTROL Board
complying with ErP directive
complying with ErP directive
5. "SECTION 12 CIRCUIT
BOARDS"
BOARDS"
A-(1)
13
Change the part number for CONTROL Board
Assembly complying with ErP directive
Assembly complying with ErP directive
6. "SECTION 13 PARTS
LOCATION AND MECHANICAL
PARTS LIST"
LOCATION AND MECHANICAL
PARTS LIST"
A-(1)
14
Add part numbers mounted on the CONTROL Board
Assembly complying with ErP directive
Assembly complying with ErP directive
7. "SECTION 14 REPLACEMENT
PARTS LIST"
PARTS LIST"
A-(1)
3
2 “SECTION 1 GENERAL PRECAUTIONS”
2.1.
“Section 1.1 Before Using This Manual”
There are 2 kinds of Products for UB-T880/T880W.
One is the 1st Version Product for UB-T880/T880W. The other is the 2nd Version (VE) Product for UB-T880 / T880W.
Checking a Serial Number on the name plate will enable you to define the product version as follows.
One is the 1st Version Product for UB-T880/T880W. The other is the 2nd Version (VE) Product for UB-T880 / T880W.
Checking a Serial Number on the name plate will enable you to define the product version as follows.
1. Serial Number-1: (xxxxxxAxxxx, xxxxxxBxxxx, xxxxxxCxxxx)
Refer to the following pages, paying attention to the expression "1st Version Product".
2. Serial Number-2:
(xxxxxxDxxxx, xxxxxxExxxx, or xxxxxxFxxxx)
Refer to the following pages, paying attention to the expression "2nd Version Product".
Note:
Note:
2nd Version (VE) Product has the model number label attached to the Pen Tray Front.
3. Serial Number-3: (xxxxxxGxxxx or later)
Refer to the following pages, paying attention to the expression "2nd Version Product" (except for
CONTROL Board's information.) and "2nd Version Product complying with ErP directive".
CONTROL Board's information.) and "2nd Version Product complying with ErP directive".
Note:
Serial Number-3's constitution is the same as Serial Number-2's except for CONTROL Board.
4
3 “SECTION 9 TROUBLESHOOTING”
3.1.
“Section 9.4 Others”
Symptom
Possible Cause
Check Point
1. Power LED does not
light up.
light up.
1. Power SW / LED Board problem
1. Restart the elite-Panaboard, and then check the Power LED
status.
2. Check the soldering condition of SW300 and D301 on the Power
SW / LED Board.
3. Replace faulty parts or Power SW / LED Board.
status.
2. Check the soldering condition of SW300 and D301 on the Power
SW / LED Board.
3. Replace faulty parts or Power SW / LED Board.
2. The connection between CONTROL Board
and Power SW / LED Board is not proper.
and Power SW / LED Board is not proper.
1. Restart the elite-Panaboard, and then check the Power LED
status.
2. Check the connection between CN300 (on the Power SW / LED
Board) and CN206 (on the CONTROL Board).
3. Replace the cable between CN300 and CN206.
status.
2. Check the connection between CN300 (on the Power SW / LED
Board) and CN206 (on the CONTROL Board).
3. Replace the cable between CN300 and CN206.
3. CONTROL Board or POWER Board
problem
problem
1. Restart the elite-Panaboard, and then check the Power LED
status.
2. Check the soldering condition of Q200 on the CONTROL Board.
3. Check the following signals on the CONTROL Board.
(1) CN208-1st pin: Approx. 5 V?
status.
2. Check the soldering condition of Q200 on the CONTROL Board.
3. Check the following signals on the CONTROL Board.
(1) CN208-1st pin: Approx. 5 V?
→ If no, POWER Board has some problems.
(2) IC217-3rd pin: Approx. 3.3 V?
→ If no, CONTROL Board has some problems.
4. Replace faulty parts, POWER Board, or CONTROL Board.
4. Automatic power-off function is
operating.
(Only applied to Serial Number
xxxxxxGxxxx or later corresponding
to "2nd Version Product complying
with ErP directive")
operating.
(Only applied to Serial Number
xxxxxxGxxxx or later corresponding
to "2nd Version Product complying
with ErP directive")
Note:
If you switch off the computer
connected to the elite
Panaboard, or unplug the USB
cable, the elite Panaboard turns
off automatically after about 60
minutes.
connected to the elite
Panaboard, or unplug the USB
cable, the elite Panaboard turns
off automatically after about 60
minutes.
1. Restart the elite-Panaboard, and then check the
Power LED status.
Power LED status.