Panasonic KV-SL3066 / KV-SL3056 / KV-SL3055 / KV-SL3036 / KV-SL3035 (serv.man5) Service Manual / Supplement ▷ View online
3
KV-SL3066/KV-SL3056/KV-SL3055/KV-SL3036/KV-SL3035
Changing point / Reference plate
After
Current
PNZUS1570M/Reference plate (F)
PNZUS1571M/Reference plate (B)
Difference between
PNZUS1570M
and
PNZUS1571M
*The thickness of the white sheet is different.
䠄PNZUS1570M䠖0.3mm, PNZUS1571M: 0.5mm䠅
(
Interchangeability Code : B
Case (1) :
Original part : PNZUS1570M
э SetProduction : Early set only
* Production until June 2018.
Case (2-1) :
New part : PNZUS1571M
э SetProduction : Late set only
* From July 2018 production.
Case (2- 2) :
Case of using new part (PNZUS1571M ) for products before July 2018:
* Need to change with PNZES1571M1(Scanning Glass (B))
July 2018
Case (1):PNZUS1570M
Case (2-1): PNZUS1571M
Case (2- 2): PNZUS1571M
+
PNZES1571M1
(Scanning Glass (B) )
Original Early
New
New
Late
Case (1)
Case (2 -1)
Case (2 -2)
Production :
figure.1
4
KV-SL3066/KV-SL3056/KV-SL3055/KV-SL3036/KV-SL3035
1.2.
Lower Chassis 2
Changed from Original Service Manual as section 8.5.
1.2.1.
Bottom Plate
1.2.2.
Platen Motor
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the screw A and the USB Earth Plate.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Tilt the Bottom Plate and remove it from the hole.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Tilt the Bottom Plate and remove it from the hole.
Reassembling Note:
Install the Bottom Plate with screws C and F first and then
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
While slanting the Bottom Plate, insert it into the hole.
(1) Remove the Bottom Plate.
(See 1.2.1. Bottom Plate)
(2) Remove the CONTROL Board.
(See 1.2.5. CONTROL Board)
(3) Remove the Polyslider and Gear.
(4) Remove the screw C.
(5) Remove the Platen Motor with Motor Plate.
(6) Remove the 2 screws G and remove the Platen Motor from
(4) Remove the screw C.
(5) Remove the Platen Motor with Motor Plate.
(6) Remove the 2 screws G and remove the Platen Motor from
the plate.
(7) Disconnect the connector.
Hole
Bottom Plate
Bottom Plate
F
A
USB Earth Plate
Bottom Plate
Bottom Plate
C
FFC
Harness
Hole
CONTROL Board
C
G
Platen Motor
Motor Plate
G
Gear
Polyslider
Connector
5
KV-SL3066/KV-SL3056/KV-SL3055/KV-SL3036/KV-SL3035
1.2.3.
FAN
1.2.4.
Power Supply
1.2.5.
CONTROL Board
1.2.6.
Conveyor Motor
1.2.7.
STARTING SENSOR Board
(1) Remove the Bottom Plate.
(See 1.2.1. Bottom Plate)
(2) Remove 2 screws E.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(1) Remove the Bottom Plate.
(See 1.2.1. Bottom Plate)
(2) Remove the 2 screws C.
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL Board on the
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL Board on the
Power Supply.
(1) Remove the Bottom Plate.
(See 1.2.1. Bottom Plate)
(2) Disconnect all connectors (8 cable connectors and 5 FFC
cables) to CONTROL Board.
(3) Remove the CONTROL Board.
Power Supply
FAN
C
E
CONTROL Board
FFC
Harness
(1) Remove the CONTROL Board.
(See 1.2.5. CONTROL Board)
(2) Remove the STARTING SENSOR Board
Assembly.(8.5.7) and remove the Dust Prevent
Sheet when the replacing of the Conveyor Motor
with Cable for KV-SL3066.
Sheet when the replacing of the Conveyor Motor
with Cable for KV-SL3066.
(3) Remove the Side Plate Assembly.
(See 8.4.5. Side Plate
Assembly)
(4) Remove the 2 screws A.
(5) Remove the connector and remove Conveyor Motor.
(5) Remove the connector and remove Conveyor Motor.
(1) Remove the CONTROL Board.
(See 1.2.5. CONTROL Board)
(2) Remove the 3 screws C.
(3) Remove the STARTING SENSOR Board Assembly.
(4) Remove the screw C, disconnect the connector.
(5) Remove the STARTING SENSOR Board.
(3) Remove the STARTING SENSOR Board Assembly.
(4) Remove the screw C, disconnect the connector.
(5) Remove the STARTING SENSOR Board.
Conveyor Motor
A
STARTING SENSOR
Board Assembly
Board Assembly
C
C
STARTING SENSOR Board
Connector
6
KV-SL3066/KV-SL3056/KV-SL3055/KV-SL3036/KV-SL3035
1.2.8.
Wiring of Lower Chassis