Panasonic KV-SL3066 / KV-SL3056 / KV-SL3055 / KV-SL3036 / KV-SL3035 (serv.man2) Service Manual ▷ View online
37
8.3.8.
Wiring of Upper Chassis
38
8.4.
Lower Chassis 1
8.4.1.
Paper Feed Roller
8.4.2.
CIS (F)
(1) Remove the Paper Feed Roller Assembly.
(See
Appendix
(
Operating Manual P.61
)
)
(2) Push the tab (arrow
1
) to remove the Feed Roller.
(3) Remove the rollers (arrow
2
) from the shaft.
Reassembling Note:
Make sure the left (white) and right (black) paper feed rollers
are installed correctly.
Make sure the left (white) and right (black) paper feed rollers
are installed correctly.
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Open the ADF Door.
(3) Remove screw C.
(3) Remove screw C.
(4) Unlock the 3 hooks.
(5) Remove the Scanning Glass (F).
(6) Take out the CIS(F) from the Main Unit.
(6) Take out the CIS(F) from the Main Unit.
White
Black
Feed Roller
2
1
2
2
Tab
C
Scanning Glass (F)
ADF Door
Hook
Top Front Cover
CIS (F)
Scanning Glass (F)
39
8.4.3.
Reference Plate (B)
8.4.4.
DOOR DETECTION Board
(1) Remove the CIS (F).
(See 8.4.2. CIS (F))
(2) Remove the Screw E.
(3) Remove the Spring.
(4) Remove the Slider in the direction of the arrows.
(3) Remove the Spring.
(4) Remove the Slider in the direction of the arrows.
Reassembling Note:
(1) Slider Gear Positioning.
Move the Slider Gear to the position where the gear
touches the rib.
touches the rib.
(2) Slider Positioning.
Insert the Slider into the Slider groove.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
(5) Remove the Polyslider and the Reshuffling Lever.
(6) Remove the Reference Plate (B).
(6) Remove the Reference Plate (B).
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the DOOR DETECTION Board, while unlocking the
hook.
(3) Disconnect the connector.
Rib
Slider Gear Positioning
Slider Gear
Rib
Slider Positioning
Slider
Slider groove
E Spring
Slider
Reference Plate (B)
Reshuffling Lever
Polyslider
DOOR
DETECTION Board
DETECTION Board
Hook
40
8.4.5.
Side Plate Assembly
8.4.6.
Conveyor roller
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the screws A and remove the Earth Plate with the
wire.
(3) Remove the 2 screws C and the Side Plate Assembly.
Reassembling Note:
Make sure to position the Idle Pulley of the Side Plate
Assembly outside of the Conveyor Belt 2.
Assembly outside of the Conveyor Belt 2.
(1) Remove the Side Plate Assembly and Conveyor Belt 2.
(See 8.4.5. Side Plate Assembly)
(2) Pull and remove the Pulley of the Conveyor Roller (arrow
2
),
while unlocking the hook (arrow
1
) on the Pulley.
Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Conveyor Roller by pulling the
Pulley.
(3) Slide and remove the bearing from the Conveyor Roller
(arrow
3
).
(4) Open and remove the Feed Roller Cover.
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
4
)
(6) Unlock the Conveyor Roller by turning the Conveyor Roller
Bearing (arrow
5
),
(7) Slide the Conveyor Roller with the Conveyor Roller Bearing
(arrow
6
) and remove it (arrow
7
).
(8) Remove the Support Bearing.
(9) Remove the Polyslider.
(10) Remove the Conveyor Roller Bearing from the Conveyor
(10) Remove the Conveyor Roller Bearing from the Conveyor
Roller.
Idle Pulley
Idle Pulley
Conveyor Belt 2
tension
C
A
Earth Plate
Side Plate Assembly
C
Bearing
Pulley
Conveyor
Roller
Roller
Hook
1
2
3
Feed Roller
Cover
Cover
Conveyor Roller
Conveyor
Roller
Bearing
Roller
Bearing
Support
Bearing
Bearing
4
6
5
7
Conveyor Roller Bearing
Support Bearing
Polyslider
Click on the first or last page to see other KV-SL3066 / KV-SL3056 / KV-SL3055 / KV-SL3036 / KV-SL3035 (serv.man2) service manuals if exist.