Panasonic KV-S7075C (serv.man4) Service Manual / Supplement ▷ View online
7
4 "SECTION 9 SERVICE UTILITY & SELF TEST"
4.1.
“Section9.1 Main Menu Indication for Service Utility”
This section describes the functions of the service utility software, such as adjustments, diagnosis, configuration and maintenance.
This utility software also includes the functions contained in the User Utility software enclosed in the scanner.
Executing “ServiceUtility.exe” will allow you to operate all the functions found in this service utility software.
Note
This utility software also includes the functions contained in the User Utility software enclosed in the scanner.
Executing “ServiceUtility.exe” will allow you to operate all the functions found in this service utility software.
Note
• This utility software is not included with the scanner. Please call service or technical support to obtain the utility
software.
• This software should be used only by an authorized service technician. Improper use of this software may cause
damage to the scanner.
8
4.2.
“Section 9.2 List of Functions for Service Utility”
Service Utility item list is as follows.
Note:
When two or more scanners are connected to a PC, execute “Select Scanner” to specify the scanner before using
Service Utility features. The procedure is as follows.
1. Click “Select Scanner” on the main menu.
2. Select the product number of the scanner to evaluate.
Service Utility features. The procedure is as follows.
1. Click “Select Scanner” on the main menu.
2. Select the product number of the scanner to evaluate.
Item
Purpose
Remarks
Scanner Status
*2
Used to indicate scanner status (Ready, Error, or Caution)
2
Scanner Information
*2
Used to indicate scanner information such as Model, firmware
version, Gate Array version, board revision, memory size,
interface, Interface condition, etc.
version, Gate Array version, board revision, memory size,
interface, Interface condition, etc.
2
Scanner Counter Update All Counters
*2
Used to update the values of System Counter, Flatbed Counter,
Cleaning Roller Counter, and Replacing Roller Counter
Cleaning Roller Counter, and Replacing Roller Counter
1, 6
Clear Counter
(After Clean Roller)
(After Clean Roller)
*2
Used to reset the Roller Cleaning Counter to zero after cleaning
the rollers
the rollers
1, 6
Clear Counter
(After Replace Roller)
(After Replace Roller)
*2
Used to reset the Roller Replacement Counter to zero after
replacing the rollers
replacing the rollers
1, 6
Scanner Condition Sleep Mode
*2
1. Used to set “Waiting Time” before the scanner enters Sleep
Mode
Mode
2. Used to set “Waiting Time” before entering the
Standby Mode
Standby Mode
1
Clean Imprinter
*1 *2
Used to clean the ink jet head of the imprinter
6
Buzzer Setting
*2
Used to set the Buzzer to ON or OFF condition
1
User Shading
*2
Used to execute shading correction by the user, or to restore the
shading data to the default (Factory-setting)
shading data to the default (Factory-setting)
4
Caution Setting
*2
Used to set the number of the document scanned for the
Service Utility to inform the user of the caution information (roller
replacement timing and roller cleaning timing)
Service Utility to inform the user of the caution information (roller
replacement timing and roller cleaning timing)
1, 3
Set Default
Used to set “Sleep Mode”
(Sleep and Standby)
, “Caution
Setting”, and “Feed Speed” to their default
3
Test
LED
Used to periodically light the indicators on the front cover
5
Key / Sensor
Used to do key or sensor ON/OFF tests
5
Sensor Sensitive Level
Used to check the status (Offset level, Slice level) of each Sensor
(Waiting, Starting, Skew (L), Skew (R), Ending)
(Waiting, Starting, Skew (L), Skew (R), Ending)
5
Feed Motor
Used to check the Paper Feed Motor’s rotation
5
Conveyor Motor
Used to check the Conveyor Motor’s rotation
5
Hopper Drive
Used to check the Hopper UP / DOWN mechanism
5
Feed
Used to check paper-feed operation
5
Sleep Mode
1. Used to check whether the sleep mode function works properly
2. Used to check whether the Standby mode function
works properly
works properly
5
CIS Level
Used to check the peak output-level after setting CIS LED lighting
level on each side
level on each side
5
CIS Focus
Not Used
—
Image Sensor Output
Used to check if CIS operates normally by outputting the
CIS's output level, or if a dust is attached on the Image
Sensor Cover
CIS's output level, or if a dust is attached on the Image
Sensor Cover
5
Double Feed
Used to check the level of the Double Feed Detector (R)
(Response level) after setting the ultrasonic emission level of the
Double Feed Detector (G)
(Response level) after setting the ultrasonic emission level of the
Double Feed Detector (G)
5
Memory
Used to execute the memory R/W test
5
9
Note
*1
: This item is available only if the optional Imprinter is installed to the scanner.
*2
: These items are also available in the User Utility software.
*3
: This setting is needed when replacing CONTROL Board or IC1003.
Remarks
1. Parameter setting by user
2. Status indication
3. Parameter setting by service person
4. Adjustment
5. Diagnosis
6. Maintenance
2. Status indication
3. Parameter setting by service person
4. Adjustment
5. Diagnosis
6. Maintenance
Adjust
Shading
Used to execute shading correction
4
All Position
1. Used to automatically adjust scanning length, vertical,
and horizontal position adjustment for front and back sides in
ADF mode
2. Used to automatically adjust scanning length, vertical, and
Horizontal position adjustment in Flatbed mode
and horizontal position adjustment for front and back sides in
ADF mode
2. Used to automatically adjust scanning length, vertical, and
Horizontal position adjustment in Flatbed mode
4
Individual Position
1. Used to execute automatic length, vertical, and horizontal
position adjustment for front and back sides in ADF mode
individually and used to execute automatic length, vertical, and
horizontal position adjustment in Flatbed mode individually
2. Used to manually adjust scanning length, vertical, and
horizontal position for front and back sides in ADF mode and
used to manually adjust scanning length, vertical, and
horizontal position adjustment in Flatbed mode
position adjustment for front and back sides in ADF mode
individually and used to execute automatic length, vertical, and
horizontal position adjustment in Flatbed mode individually
2. Used to manually adjust scanning length, vertical, and
horizontal position for front and back sides in ADF mode and
used to manually adjust scanning length, vertical, and
horizontal position adjustment in Flatbed mode
4
Double Feed
Used to correct the Double Feed Detector’s ultrasonic emission
level automatically or manually
level automatically or manually
4
USB ID
*3
Used to set a USB ID for the scanner, connected to the PC
3
Feed Speed
Used to change the paper feed speed
3
Other
Save Information
*2
Used to save the scanner and PC information
1
Download the latest version Click “Download the latest version” to open the site
for Panasonic scanner products that provides the
scanner software to be downloaded.
scanner software to be downloaded.
6
Save Log
Click “Save Log” to open “Save As” dialog-box.
Then after renaming a log file, perform “Save” to save
it.
Then after renaming a log file, perform “Save” to save
it.
6
Item
Purpose
Remarks
10
4.3.
“Section 9.3 Operation”
4.3.1.
“Section 9.3.5 Scanner Condition”
Note: *Standby (Factory setting)
For KV-S7075C-U: 30 minutes
Except for KV-S7075C-U: Disable
Except for KV-S7075C-U: Disable
Note that “Standby Mode” will be set to “Disable” when performing “Set Default”.
(If you want to set “Standby Mode” to “Enable” equivalent to setting “Waiting Time”, “Sleep Mode” setting
will be required.)
(If you want to set “Standby Mode” to “Enable” equivalent to setting “Waiting Time”, “Sleep Mode” setting
will be required.)
Item
Operation
Default
Remarks
Sleep Mode
1. Click “Sleep Mode” on the main menu (Service Utility).
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
Then, set "Waiting Time" (Unit: minutes) to specify
the amount of time until the scanner enters
Standby Mode.
the amount of time until the scanner enters
Standby Mode.
3. Click “OK” to renew the setting.
Sleep:
15 minutes
*Standby:
Disable
When returning back to the
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Clean Imprinter
1. Click “Clean Imprinter” on the main menu to clean the
imprinter’s print head.
imprinter’s print head.
—
This item is available only if
the optional Pre-imprinter is
installed to the scanner.
the optional Pre-imprinter is
installed to the scanner.
Buzzer Setting
1. Click “Buzzer Setting” on the main menu.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
—
User Shading
1. Click “User Shading” on the main menu.
2. Click “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
2. Click “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
a. When selecting “Restore Default”, the factory-setting
data will be overwritten in stead of the current
shading data.
b. The following procedures from “3.” onwards are
available only for selecting “Start Shading”.
data will be overwritten in stead of the current
shading data.
b. The following procedures from “3.” onwards are
available only for selecting “Start Shading”.
3. Clean the conveyor, rollers, and ADF Glasses
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the included Shading Paper or Shading Paper
(Part No.: See 14.7.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to finish the shading correction.
9. Click “Close” to return to the main menu.
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the included Shading Paper or Shading Paper
(Part No.: See 14.7.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to finish the shading correction.
9. Click “Close” to return to the main menu.
—
1. Before executing the
shading function, be sure to
clean the ADF Glasses,
rollers, and conveyors
related to
shading function, be sure to
clean the ADF Glasses,
rollers, and conveyors
related to
conveying
documents
.
2. Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
Caution Setting
1. Click “Caution Setting” on the main menu.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
Clean:
20000
Replace:
300000
Set Default
1. Click “Set Default” on the main menu.
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”
(Sleep and Standby)
,
“Caution Setting”, and “Feed Speed”.
3. Click “Close” to return to the main menu.
3. Click “Close” to return to the main menu.
—
Click on the first or last page to see other KV-S7075C (serv.man4) service manuals if exist.