Panasonic KV-S7065C (serv.man4) Service Manual ▷ View online
7.2.5. Cleaning Sensors and Reflector Sheets-1 (Paper and Waiting Sensors, Double
Feed Detector)
How to clean sensors (detectors) and reflectors.
Remove the brush from the accessory Blower and blow off the dirt with the blower.
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Push the ADF Door Release to open the ADF Door.
(See 7.2.1-(2).)
(3) Blow off the dirt on the surface of the Paper Sensor and
Waiting Sensor with an accessory blower.
(4) And also blow off the dirt on the surface of the Reflector
Sheet for the Waiting Sensor with the accessory blower.
(Top Front View)
(5) Blow off the dirt from the Double Feed Detector (G) and
Double Feed Detector (R) with the accessory blower.
(6) Close the ADF Door slowly until it clicks into place.
(See 7.2.1-(7).)
(Front View)
33
KV-S7065CSERIES
7.2.6. Cleaning Sensors and Reflector Sheets-2 (Starting, Skew (L), Skew (R), and
Ending Sensors)
How to clean sensors (detectors) and reflectors.
Remove the brush from the accessory Blower and blow off the dirt with the blower.
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Fold the Hopper Tray in the direction of the arrow, and pull
the Exit Door Release to open the Exit Door.
(See 7.2.3-(2).)
(See 7.2.3-(2).)
(3) Blow off the dirt on the surface of the Starting, Skew (L),
Skew (R), and Ending Sensors with the accessory blower.
(Right Side View)
(4) And blow off the dirt from the Reflector Sheets for the
Starting, Skew (L), Skew (R), and Ending Sensors with the
blower.
blower.
(5) Close the Exit Door slowly until it clicks into place and put
back the Hopper Tray to the original position.
(See 7.2.3-(5).)
(See 7.2.3-(5).)
(Front View)
34
KV-S7065CSERIES
7.2.7. Cleaning Flatbed Glass
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Fold the Hopper Tray in the direction of the arrow.
(3) Open the Document Cover.
(4) Clean up the surface of Flatbed Glass with the accessory
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper) to remove the dirt.
(Also clean up the surface of the Flatbed Sheet, as
required.)
Cleaning Paper) to remove the dirt.
(Also clean up the surface of the Flatbed Sheet, as
required.)
(5) Close the Document Cover and put back the Hopper Tray
to the original position.
35
KV-S7065CSERIES
7.3. Replacing Limited Life Parts
7.3.1. Replacing Paper Feed Roller Module
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Push the ADF Door Release to open the ADF Door.
(See 7.2.1-(2).)
(3) Pull down the Paper Feed Roller Module, holding both sides
of the module plate in the direction of the arrow.
(4) Remove the Paper Feed Roller Module as shown on the
figure.
(5) Open the optional Roller Exchange Kit (KV-SS015), and
take out the Paper Feed Roller Module.
(6) Install a new Paper Feed Roller Module.
36
KV-S7065CSERIES
Click on the first or last page to see other KV-S7065C (serv.man4) service manuals if exist.