Panasonic KV-S4065CL / KV-S4065CW / KV-S4085CL / KV-S4085CW Service Manual / Supplement ▷ View online
10
4.2.
List of Functions for Service Utility
Service Utility item list is as follows.
Note:
When two or more scanners are connected to a PC, execute “Select Scanner” to specify the scanner before evaluating.
The procedure is as follows.
1. Click “Select Scanner” on the main menu.
2. Select the product number of the scanner to evaluate.
The procedure is as follows.
1. Click “Select Scanner” on the main menu.
2. Select the product number of the scanner to evaluate.
Item
Purpose
Remarks
Scanner Status
*2
Used to indicate scanner status (Ready, Error, or Caution)
2
Scanner Information
*2
Used to indicate scanner information such as Model, firmware
version, board revision, memory size, interface, Interface
condition, etc.
version, board revision, memory size, interface, Interface
condition, etc.
2
Scanner Counter Update All Counters
*2
Used to update the values of System Counter, Cleaning Roller
Counter, and Replacing Roller Counter
Counter, and Replacing Roller Counter
1, 6
Clear Counter
(After Clean Roller)
(After Clean Roller)
*2
Used to reset the Roller Cleaning Counter to zero after cleaning
the rollers
the rollers
1, 6
Clear Counter
(After Replace Roller)
(After Replace Roller)
*2
Used to reset the Roller Replacement Counter to zero after
replacing the rollers
replacing the rollers
1, 6
Scanner Condition Sleep Mode
*2
1. Used to set “Waiting Time” before entering the Sleep Mode
2. Used to set “Waiting Time” before entering the
Standby Mode
Standby Mode
1
Clean Imprinter
*1 *2
Used to clean the ink jet head of the imprinter
6
Buzzer Setting
*2
Used to set the Buzzer ON/OFF condition
1
User Shading
*2
Used to execute shading correction at the user side, or to restore
the shading data to the default (Factory-setting)
the shading data to the default (Factory-setting)
4
Caution Setting
*2
Used to set the number of the document scanning that enables
the Service Utility to inform the caution information (roller
replacement timing and roller cleaning timing)
the Service Utility to inform the caution information (roller
replacement timing and roller cleaning timing)
1, 3
Set Default
1. Used to set “Sleep Mode”
(Sleep and Standby)
,
“Caution Setting”, and “Feed Speed” to the default
2. Used to set “Thickness”, “ADF”, and “Hopper” on the
Control Panel to the default
Thickness: Standard
ADF: Auto
Hopper: Low (300 sheets)
2. Used to set “Thickness”, “ADF”, and “Hopper” on the
Control Panel to the default
Thickness: Standard
ADF: Auto
Hopper: Low (300 sheets)
3
11
Note
*1
: This item is available only if the optional Imprinter is installed to the scanner.
*2
: These items are also available in User Utility software.
*3
: This setting is needed when replacing CONTROL Board or IC1008.
Test
LED
Used to periodically light the indicators on the front cover
5
Key / Sensor
Used to do keys' or sensors' ON/OFF test
5
Sensor Sensitive Level
Used to check the status (Offset level, Slice level) of each Sensor
(Waiting, Starting, Skew (L), Skew (R), Exit, Paper Jam)
(Waiting, Starting, Skew (L), Skew (R), Exit, Paper Jam)
5
Feed Motor
Used to check Paper Feed Motor and Separation Motor rotation
5
Conveyor Motor
Used to check Conveyor Motor rotation
5
DFP Pressure Drive
Used to check DFP Pressure Motor rotation
5
Hopper Drive
Used to check Hopper Motor rotation
5
Feed
Used to check paper feed condition
5
Slip Detect Sensor
Used to check Slip Detect Sensors (1,2) and their rollers
mechanism
mechanism
5
Sleep Mode
1. Used to check whether the sleep mode function works properly
2. Used to check whether the Standby mode function
works properly
works properly
5
CIS Level
Used to check the peak output-level after setting CIS LED lighting
level on each side
level on each side
5
CIS Focus
Used to check whether the CIS focus point is appropriate to scan
documents, and used to adjust the focus, showing the CIS gray
density level on the display
documents, and used to adjust the focus, showing the CIS gray
density level on the display
4,5
Image Sensor Output
Used to check whether CIS operates normally by outputting the
CIS's output level or whether a dust is attached on the Image
Sensor Cover
CIS's output level or whether a dust is attached on the Image
Sensor Cover
5
Double Feed
1. For KV-S4085CL/ CW Series
Used to check the levels of the Double Feed Detector L(R),
C(R), and R(R) (Response level) after setting the ultrasonic
emission level of the Double Feed Detectors L(G), C(G),
and R(G
Used to check the levels of the Double Feed Detector L(R),
C(R), and R(R) (Response level) after setting the ultrasonic
emission level of the Double Feed Detectors L(G), C(G),
and R(G
)
2. For KV-S4065CL/CW Series
Used to check the level of the Double Feed Detector (R)
(Response level) after setting the ultrasonic emission level of the
Double Feed Detector (G)
Used to check the level of the Double Feed Detector (R)
(Response level) after setting the ultrasonic emission level of the
Double Feed Detector (G)
5
Memory
Used to execute memory R/W test
5
Roller Pressure Sensor Level
Used to check the level of the pressure exerted by the Hopper
2
Adjust
Shading
Used to execute shading correction
4
All Position
Used to adjust scanning length, vertical, and horizontal position
adjustment for front and back sides automatically
adjustment for front and back sides automatically
4
Individual Position
1. Used to execute automatic length, vertical or horizontal
position adjustment for front and back sides, individually
2. Used to adjust scanning length, vertical, or horizontal position
for front and back sides manually
position adjustment for front and back sides, individually
2. Used to adjust scanning length, vertical, or horizontal position
for front and back sides manually
4
Double Feed
Used to correct the Double Feed Detector’s ultrasonic emission
level automatically or manually
level automatically or manually
4
Bent Paper Sensor
Used to correct the Bent Paper Sensor’s sending level
automatically or manually
automatically or manually
4
USB ID
*3
Used to set a USB ID for the scanner, connected to the PC
3
Feed Speed
Used to change the paper feed speed
3
Other
Save Information
*2
Used to save the scanner and PC information
1
Download the latest version Click “Download the latest version” to open the site
for Panasonic scanner products that provides the
scanner software to be downloaded.
scanner software to be downloaded.
6
Save Log
Click “Save Log” to open “Save As” dialog-box.
Then after renaming a log file, perform “Save” to save
it.
Then after renaming a log file, perform “Save” to save
it.
6
Item
Purpose
Remarks
12
Remarks
1. Parameter setting by user
2. Status indication
3. Parameter setting by service person
4. Adjustment
5. Diagnosis
6. Maintenance
2. Status indication
3. Parameter setting by service person
4. Adjustment
5. Diagnosis
6. Maintenance
13
4.3.
"Section 9.3. Operation"
4.3.1.
“Section 9.3.5 Scanner Condition”
Note: *Standby (Factory setting)
For KV-S4065CL-U / S4065CW-U / S4085CL-U/ S4085CW-U: 30 minutes
Except for KV-S4065CL-U / S4065CW-U / S4085CL-U/ S4085CW-U: Disable
Except for KV-S4065CL-U / S4065CW-U / S4085CL-U/ S4085CW-U: Disable
Note that “Standby Mode” will be set to “Disable” when performing “Set Default”.
(If you want to set “Standby Mode” to “Enable” equivalent to setting “Waiting Time”, “Sleep Mode” setting
will be required.)
(If you want to set “Standby Mode” to “Enable” equivalent to setting “Waiting Time”, “Sleep Mode” setting
will be required.)
Item
Operation
Default
Remarks
Sleep Mode
1. Click “Sleep Mode” on the main menu (Service Utility).
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
2. Set “Waiting Time” (Unit: minutes) to specify the amount of
time until the scanner enters the sleep mode.
Then, set "Waiting Time" (Unit: minutes) to specify
the amount of time until the scanner enters
Standby Mode.(Or set "Disable".)
the amount of time until the scanner enters
Standby Mode.(Or set "Disable".)
3. Click “OK” to renew the setting.
Sleep:
15 minutes
15 minutes
*Standby:
Disable
Disable
When returning back to the
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Clean Imprinter
1. Click “Clean Imprinter” on the main menu to clean the
imprinter’s print head.
imprinter’s print head.
—
This item is available only if
the optional Pre-imprinter
and/or Post-imprinter is
installed to the scanner.
the optional Pre-imprinter
and/or Post-imprinter is
installed to the scanner.
Buzzer Setting
1. Click “Buzzer Setting” on the main menu.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Set “Buzzer Setting (ON or OFF)” on the “Buzzer Setting”
dialog box.
3. Click “OK” to renew the setting.
—
User Shading
1. Click “User Shading” on the main menu.
2. Push “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
2. Push “Start Shading” or “Restore Default” on the “User
Shading” dialog box.
Note:
a. When selecting “Restore Default”, the factory-setting
data will be overwritten in stead of the current
shading data.
b. The following procedures “3” or more are available
only for selecting “Start Shading”.
data will be overwritten in stead of the current
shading data.
b. The following procedures “3” or more are available
only for selecting “Start Shading”.
3. Clean the conveyor, rollers, and Image Sensor Cover
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the accessory Shading Paper or Shading Paper
(Part No.: See 14.6.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to return to the main menu.
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the accessory Shading Paper or Shading Paper
(Part No.: See 14.6.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display. And click “OK”
8. Click “OK” to return to the main menu.
—
1. Before executing the
shading function, be sure to
clean the Image Sensor
Cover, rollers, and
conveyors related to
shading function, be sure to
clean the Image Sensor
Cover, rollers, and
conveyors related to
conveying documents
.
2. Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
Caution Setting
1. Click “Caution Setting” on the main menu.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
2. Change the parameter value on the “Caution Setting”
dialog box.
3. Click “OK” to renew the setting.
Clean:
20000
Replace:
400000
Set Default
1. Click “Set Default” on the main menu.
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”
2. Click “Set Default” on the “Set Default” dialog box to set
the default values for “Sleep Mode”
(Sleep and
Standby)
,, “Caution Setting”, and “Feed Speed”.
3. Click “Close” to return to the main menu.
—
Note: Default (Control-
Panel)
Clicking "Set Default"
also enables the paper
feed condition on the
scanner to be set as
follows.
Thickness: Standard
ADF: Auto
Hopper: Low (300 sheets)
also enables the paper
feed condition on the
scanner to be set as
follows.
Thickness: Standard
ADF: Auto
Hopper: Low (300 sheets)
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4085CL / KV-S4085CW service manuals if exist.