Panasonic KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN (serv.man2) Service Manual / Supplement ▷ View online
5
2.1.2.
"Section 8.2.3 Post-imprinter Door (Imprinter Cover)"
(1) Open the Post-imprinter Door.
(2) In the direction of the arrow, pull the right tip of the
Post-imprinter Door along the groove.
Then pull the left tip of the Post-imprinter Door
backward to remove the door.
Post-imprinter Door along the groove.
Then pull the left tip of the Post-imprinter Door
backward to remove the door.
6
2.2.
"Section 8.4 Board Assembly"
2.2.1.
"Section 8.4.1 CONTROL Board and DRIVE Board"
(1) Remove the Right Cover. (See 8.2.1.)
(2) Remove the screw (a), screw (b), and 2 screws (c) from the
back.
back.
(3) Remove the screw from the right.
(4) Release the connector wires from the 3 wire clamps.
(5) Pull out the Board Plate Assembly after releasing the
connector wires from the 5 wire clamps.
(5) Pull out the Board Plate Assembly after releasing the
connector wires from the 5 wire clamps.
Reassembling Note:
Make sure to fasten the cables with the clamper
so that the bundle of single-wire is located on the
multi-wire cables (Shield cable and gray color
cable).
so that the bundle of single-wire is located on the
multi-wire cables (Shield cable and gray color
cable).
7
3 “SECTION 9 SERVICE UTILITY & SELF TEST”
3.1.
“Section 9.3 Operation”
3.1.1.
“Section 9.3.1 Scanner Status”
8
3.1.2.
“Section 9.3.7 Adjustment”
Item
Operation
Default
Remarks
Shading
1. Click “Shading” on the main menu.
2. Confirm the message “The data of User Shading will be
also overwritten” on the display.
And if the message is acceptable, click “OK”.
Note:
2. Confirm the message “The data of User Shading will be
also overwritten” on the display.
And if the message is acceptable, click “OK”.
Note:
This procedure is avaiable only after executing User
Shading.
Shading.
3. Clean the conveyor, rollers, and Image Sensor Cover
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the accessory Shading Paper or Shading Paper
(Part No.: See 14.6.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display.
8. Click “OK” to return to the main menu.
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
And click “OK”.
5. Set the accessory Shading Paper or Shading Paper
(Part No.: See 14.6.) on the Hopper Tray in landscape
orientation.
6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display.
8. Click “OK” to return to the main menu.
—
Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
completed, don’t stop the
process by opening any
doors or turning off the
scanner.
All Position
1. Set 2 pcs of test chart A (Part No.: See 14.6.) on the Hopper
Tray in portrait orientation.
2. Click “All position” on the main menu to execute scanning
position and length adjustment.
3. Check the result.
4. Click “OK” to return to the main menu.
Tray in portrait orientation.
2. Click “All position” on the main menu to execute scanning
position and length adjustment.
3. Check the result.
4. Click “OK” to return to the main menu.
—
Set 2 pcs of test chart A in
order.
1st page: Front side
2nd page: Back side
order.
1st page: Front side
2nd page: Back side
Individual Position 1. Adjust Automatically.
a. Set test chart A (Part No.: See 14.6.) on the Hopper Tray.
b. Click “Individual Position” on the main menu.
c. Click one of 5 “Adjust Automatically” buttons on the
“Individual Position” dialog box to execute the
adjustment.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” to return to the main menu.
b. Click “Individual Position” on the main menu.
c. Click one of 5 “Adjust Automatically” buttons on the
“Individual Position” dialog box to execute the
adjustment.
d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” to return to the main menu.
2. Adjust Manually.
a. Click “Individual Position” on the main menu.
b. Change the parameter (mm, %) on the “Individual
Position” dialog box as required. (Refer to Remarks.)
c. Click “OK” to renew the setting, and to return to the
main menu.
a. Click “Individual Position” on the main menu.
b. Change the parameter (mm, %) on the “Individual
Position” dialog box as required. (Refer to Remarks.)
c. Click “OK” to renew the setting, and to return to the
main menu.
—
1. Adjust Automatically
5 automatic adjustment
a. Adjust Length
b. Adjust Front V. Position
c. Adjust Front H. Position
d. Adjust Back V. Position
e. Adjust Back H. Position
2. Adjust Manually
(Length)
+: Increasing the number
makes the scanning
document length
5 automatic adjustment
a. Adjust Length
b. Adjust Front V. Position
c. Adjust Front H. Position
d. Adjust Back V. Position
e. Adjust Back H. Position
2. Adjust Manually
(Length)
+: Increasing the number
makes the scanning
document length
shorter.
(Vertical Position)
+: Increasing the number
makes the document
scanning position shifted
+: Increasing the number
makes the document
scanning position shifted
upward.
(Horizontal Position)
+: Increasing the number
makes the document
scanning position shifted
to the
+: Increasing the number
makes the document
scanning position shifted
to the
left
.
Note
If the appropriate
scanning position can
not be obtained by any
of the manual
adjustments, check CIS
installation.
scanning position can
not be obtained by any
of the manual
adjustments, check CIS
installation.
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN (serv.man2) service manuals if exist.