Panasonic KV-S3065CL / KV-S3065CW (serv.man2) Service Manual / Supplement ▷ View online
9
Note:
*1
: This item is available only when the optional Imprinter is installed to the scanner
“KV-S3065CL/S3065CW Series”.
*2
: Firmware Version 1.10 or later will enable this function. (With the Version 1.00 or older,
clicking "Feed Speed"on the main menu causes an error message.)
Remarks
(1) Parameter setting by user
(2) Status indication
(3) Parameter setting by service person
(4) Adjustment
(5) Diag.
(6) Maintenance
(1) Parameter setting by user
(2) Status indication
(3) Parameter setting by service person
(4) Adjustment
(5) Diag.
(6) Maintenance
10
4.3.
“Section 9.3 Operation”
This section describes each operation (or status indication), according to the function item list shown in Sec.9.2.
4.3.1.
“Section 9.3.1 Scanner Status”
This function indicates scanner status, updating it every few seconds.
The status messages and its contents are as follows.
The status messages and its contents are as follows.
Fig. 9.3.1 Scanner Status
Classified
Code
Status Message
Contents
—
Scanner has no error.
No error
U11, U12,
U13, U14,
U15, U16,
U17
U13, U14,
U15, U16,
U17
A paper jam has occurred.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
U11: Paper feed Jam
U12: Conveyor jam1 (Paper did not reach the Starting Sensor)
U13:Conveyor jam2 (Paper did not reach the Paper Jam Sensor)
U14: Conveyor jam3 (Paper did not reach the Ending (Front) Sensor.)
U15: Conveyor jam 4 (Paper did not reach the Ending (Rear) Sensor.)
U16: Exit jam 1 (Paper did not go out of the Ending (Front) Sensor
throughout)
U17: Exit Jam2 (Paper did not go out of the Ending (Rear) Sensor
throughout)
U12: Conveyor jam1 (Paper did not reach the Starting Sensor)
U13:Conveyor jam2 (Paper did not reach the Paper Jam Sensor)
U14: Conveyor jam3 (Paper did not reach the Ending (Front) Sensor.)
U15: Conveyor jam 4 (Paper did not reach the Ending (Rear) Sensor.)
U16: Exit jam 1 (Paper did not go out of the Ending (Front) Sensor
throughout)
U17: Exit Jam2 (Paper did not go out of the Ending (Rear) Sensor
throughout)
U18
Paper remains in the scanner.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Document remains in the scanner, or dust is attached around a sensor.
U20
A skew error has occurred.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Skew error
U23
A paper double feed has occurred.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Open the scanner’s door, remove the
documents, and close the cover. Place the
documents back in the document feed tray.
Double feed error
U30
Scanner Door is open!
Please close the door.
Please close the door.
Front Door is open.
U32
Scanner Door is open!
Please close the door.
Please close the door.
Post-imprinter Door is open.
U34
Scanner Door is open!
Please close the door.
Please close the door.
Pre-imprinter Door is open.
Fxx
System error occurred!
Please consult with a service representative.
Please consult with a service representative.
Service-person call level error occurred.
—
*** Warning***
The rollers need to be cleaned.
Please clean the rollers. Please select Clear Counter
button after cleaning rollers.
The rollers need to be cleaned.
Please clean the rollers. Please select Clear Counter
button after cleaning rollers.
Warning for cleaning rollers.
—
***Warning***
The replaceable rollers (consumable) are
close to reaching their usable life.
To insure reliable operation, please replace
these rollers with Roller Exchange Kit for your
specific scanner. After replacing the rollers,
select the “Clear Counter” button.
The replaceable rollers (consumable) are
close to reaching their usable life.
To insure reliable operation, please replace
these rollers with Roller Exchange Kit for your
specific scanner. After replacing the rollers,
select the “Clear Counter” button.
Warning for replacing rollers.
—
***Warning***
Insufficient front light error occurred. The lamp
and/or scanning sensor need to be replaced.
Insufficient front light error occurred. The lamp
and/or scanning sensor need to be replaced.
1. The lamp have reached its life expectancy.
2. Lamp drive circuit for the front does not work properly.
2. Lamp drive circuit for the front does not work properly.
—
***Warning***
Insufficient back light error occurred. The lamp
and/or scanning sensor need to be replaced.
Insufficient back light error occurred. The lamp
and/or scanning sensor need to be replaced.
1. The lamp have reached its life expectancy.
2. Lamp drive circuit for the back does not work properly.
2. Lamp drive circuit for the back does not work properly.
—
***Warning***
The scanner’s image sensor cover is dirty and
requires routine cleaning. To insure reliable
scanning quality, open the scanner’s door
and carefully clean the scanner’s image
sensor cover.
The scanner’s image sensor cover is dirty and
requires routine cleaning. To insure reliable
scanning quality, open the scanner’s door
and carefully clean the scanner’s image
sensor cover.
The surface of Image Sensor Cover is dirty.
—
Scanner is not connected!
Scanner is not connected to PC properly.
11
4.3.2.
“Section 9.3.5 Scanner Condition”
Item
Operation
Default
Remarks
Sleep Mode
1. Click “Sleep Mode” on the main menu (Service Utility).
2. Set “Waiting Time” (minutes) to change sleep
mode.
3. Click “OK” to renew the setting.
mode.
3. Click “OK” to renew the setting.
15 minutes
When returning back to the
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Ready Mode from the Sleep
Mode, execute “Sleep
Mode” for Test (9.3.6) on the
main menu, and then click
“STOP” on the “Sleep
Mode” dialog box.
Clear Imprinter
1. Click “Clean Imprinter” on the main menu to clean an ink jet
head to print.
head to print.
—
This item is available
only when the optional
Imprinter is installed
to the scanner.
only when the optional
Imprinter is installed
to the scanner.
Paper Mode /
Buzzer Setting
Buzzer Setting
1. Click “Paper Mode / Buzzer Setting” on the main menu.
2. Set “Paper Mode (A4 or Letter)” and/or “Buzzer Setting
(ON or OFF)” on “Paper Mode / Buzzer Setting” dialog
box.
3. Click “OK” to renew the setting.
2. Set “Paper Mode (A4 or Letter)” and/or “Buzzer Setting
(ON or OFF)” on “Paper Mode / Buzzer Setting” dialog
box.
3. Click “OK” to renew the setting.
Compatible Mode 1. Click “Compatible Mode” on the main menu.
2. Set a model number to operate the scanner as the emulation
mode on “Compatible Mode” dialog box.
3. Click “OK” to renew the setting.
mode on “Compatible Mode” dialog box.
3. Click “OK” to renew the setting.
User Shading
1. Click “User Shading” on the main menu.
2. Push “Start Shading” or “Restore Default” on “User
Shading” dialog box.
2. Push “Start Shading” or “Restore Default” on “User
Shading” dialog box.
Note:
a. When selecting “Restore Default”, the factory-setting
data will be overwritten in stead of the current
shading data.
b. The following procedures “3” or more are available
only for selecting “Start Shading”.
data will be overwritten in stead of the current
shading data.
b. The following procedures “3” or more are available
only for selecting “Start Shading”.
3. Clean the conveyor, rollers, and Image Sensor Covers
according to the message on the display.
according to the message on the display.
And click “OK”.
4. Switch Reference Plates to white according to the message
on the display.
on the display.
And click “OK”.
5. Set the accessory Shading Paper or Shading Paper
(Part No.: See 14.7.) on the Hopper Tray in the following
orientation.
(Part No.: See 14.7.) on the Hopper Tray in the following
orientation.
(1) In case of KV-S3065CW
→
Landscape orientation
(2) In case of KV-S3065CL
→
Portrait orientation
And click “OK”.
6. Scan the Shading Paper.
7. Switch the Reference Plates to black according to the
message on the display.
And click “OK”.
8. Click “OK” to get back to the main menu.
7. Switch the Reference Plates to black according to the
message on the display.
And click “OK”.
8. Click “OK” to get back to the main menu.
1. Before executing the
shading function, be sure to
clean Image Sensor
Covers, rollers, and
conveyors related to
convey documents.
shading function, be sure to
clean Image Sensor
Covers, rollers, and
conveyors related to
convey documents.
2. Do not stop the shading
execution on its way and
do not open any doors.
execution on its way and
do not open any doors.
Warning Setting
1. Click “Warning Setting” on the main menu.
2. Change the parameter on “Warning Setting” dialog box.
3. Click “OK” to renew the setting.
2. Change the parameter on “Warning Setting” dialog box.
3. Click “OK” to renew the setting.
Clean:
20000
Replace:
300000
Set Default
1. Click “Set Default” on the main menu.
2. Click “Set Default” on the “Set Default” dialog box
to set “Sleep Mode”, “Warning Setting”, and “Feed
Speed” to the default.
to set “Sleep Mode”, “Warning Setting”, and “Feed
Speed” to the default.
3. Click “Close” to get back to the main menu.
—
12
4.3.3.
“Section 9.3.7 Adjust”
Note:
*1
: Firmware Version 1.10 or later will enable this function. (With the Version 1.00 or older,
clicking "Feed Speed"on the main menu causes an error message.)
Item
Operation
Default
Remarks
* USB ID
1. Click “USB ID” on the main menu to enter in the “USB ID”
dialog box.
2. Click “Set” on the “USB ID” dialog box to store a new ID
number for a new replaced CONTROL Board.
3. Click “Close” to get back to the main menu.
dialog box.
2. Click “Set” on the “USB ID” dialog box to store a new ID
number for a new replaced CONTROL Board.
3. Click “Close” to get back to the main menu.
—
*This setting is available only
for a new replaced
CONTROL Board.
for a new replaced
CONTROL Board.
*1
Feed Speed
1. Click “Feed Speed” on the main menu.
2. Change the parameter (PPS: 300 to 800).
3. Click “OK” to renew the setting, and to get back to
the main menu.
Note:
2. Change the parameter (PPS: 300 to 800).
3. Click “OK” to renew the setting, and to get back to
the main menu.
Note:
This slow thin-paper feed may reduce a
paper-jam or a double-feed.
paper-jam or a double-feed.
800
-: Decreasing the
number makes
document feed
speed slower.
number makes
document feed
speed slower.
Click on the first or last page to see other KV-S3065CL / KV-S3065CW (serv.man2) service manuals if exist.