Panasonic KV-S1057C / KV-S1027C / KV-SL1066 / KV-SL1056 / KV-SL1055 / KV-SL1036 / KV-SL1035 Service Manual ▷ View online
33
7.4.3.
Reference Plate (B)
7.4.4.
DOOR DETECTION Board
(1) Remove the CIS (F). (See
CIS (F)
(
P.32
))
(2) Remove the Screw E.
(3) Remove the spring.
(4) Remove the Slider in the direction of the arrows.
(3) Remove the spring.
(4) Remove the Slider in the direction of the arrows.
Reassembling Note:
(1) Slider Gear Positioning.
(1) Slider Gear Positioning.
Move the Slider Gear to the position where the gear
touches the rib.
touches the rib.
(2) Slider Positioning.
Insert the Slider into the Slider groove.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
(5) Remove the Polyslider and the Reshuffling Lever.
(6) Remove the Reference Plate (B).
(6) Remove the Reference Plate (B).
Rib
Slider Gear Positioning
Slider Gear Positioning
Slider Gear
Rib
Slider Positioning
Slider Positioning
Slider
Slider groove
E Spring
Slider
Reference Plate (B)
Reshuffling Lever
Polyslider
(1) Remove the Back Cover. (See
Back Cover
(
P.26
))
(2) Remove the DOOR DETECTION Board, while unlocking the
hook.
(3) Disconnect the connector.
DOOR
DETECTION Board
DETECTION Board
Hook
34
7.4.5.
Side Plate Assembly
7.4.6.
Conveyor roller
(1) Remove the Back Cover. (See
Back Cover
(
P.26
))
(2) Remove the screws A and remove the Earth Plate with the
wire.
(3) Remove the 2 screws C and the Side Plate Assembly.
Reassembling Note:
Make sure to position the Idle Pulley of the Side Plate
Assembly outside of the Conveyor Belt 2.
Assembly outside of the Conveyor Belt 2.
(1) Remove the Side Plate Assembly and Conveyor Belt 2. (See
Side Plate Assembly
(
P.34
))
(2) Pull and remove the Pulley of the Conveyor Roller (arrow
2
),
while unlocking the hook (arrow
1
) on the Pulley.
Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Conveyor Roller by pulling the
Pulley.
Pulley is locked to the Conveyor Roller by pulling the
Pulley.
(3) Slide and remove the bearing from the Conveyor Roller
(arrow
3
).
(4) Open and remove the Feed Roller Cover.
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
4
)
(6) Unlock the Conveyor Roller by turning the Conveyor Roller
Bearing (arrow
5
),
(7) Slide the Conveyor Roller with the Conveyor Roller Bearing
(arrow
6
) and remove it (arrow
7
).
(8) Remove the Support Bearing.
(9) Remove the polyslider.
(10) Remove the Conveyor Roller Bearing from the Conveyor
(10) Remove the Conveyor Roller Bearing from the Conveyor
Roller.
Idle Pulley
Idle Pulley
Conveyor Belt 2
tension
C
A
Earth Plate
Side Plate Assembly
C
Bearing
Pulley
Conveyor
Roller
Roller
Hook
1
2
3
Feed Roller
Cover
Cover
Conveyor Roller
Conveyor
Roller
Bearing
Roller
Bearing
Support
Bearing
Bearing
(9)
4
5
6
7
Conveyor Roller Bearing
Support Bearing
Polyslider
35
7.4.7.
Exit Roller
(1) Remove the Side plate Assembly (See
Side Plate Assembly
(
P.34
)) and the Conveyor Belt 2
(2) Pull and remove the Pulley of the Exit Roller (arrow
2
), while
unlocking the hook (arrow
1
) on the Pulley.
Reassembling Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Exit Roller by pulling the Pulley.
Pulley is locked to the Exit Roller by pulling the Pulley.
(3) Slide and remove the Bearing from the Exit Roller (arrow
3
).
(4) Unlock the hook of the Conveyor Roller Bearing (arrow
4
).
(5) Unlock the Exit Roller by turning the Conveyor Roller Bear-
ing (arrow
5
).
(7) Slide the Exit Roller with the Conveyor Roller Bearing and
remove it (arrow
6
).
(8) Remove the Support Bearing.
(9) Remove the polyslider.
(10) Remove the Conveyor Roller Bearing from the Exit Roller.
(10) Remove the Conveyor Roller Bearing from the Exit Roller.
Bearing
Exit Roller
Pulley
1
2
3
Hook
4
5
Exit Roller
Conveyor Roller Bearing
Support Bearing
Exit Roller
6
Conveyor Roller Bearing
Polyslider
Support Bearing
36
7.5.
Lower Chassis 2
7.5.1.
Bottom Plate
7.5.2.
Platen Motor
7.5.3.
FAN
7.5.4.
Power Supply
7.5.5.
CONTROL Board
(1) Remove the Back Cover. (See
Back Cover
(
P.26
))
(2) Remove the screw A and the USB Earth Plate.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Remove the Bottom Plate.
(3) Remove the 7 screws C.
(4) Remove the 2 screws F.
(5) Remove the Bottom Plate.
Reassembling Note:
Install the Bottom Plate with screws C and F first and then
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
install the USB Earth Plate with screw A.
Otherwise the USB Earth Plate may not contact with the
USB jack on the Control Board correctly.
(1) Remove the Bottom Plate. (See
Bottom Plate
(
P.36
))
(2) Remove the screw C.
(3) Remove the Platen Motor with Motor Plate.
(4) Remove the 2 screws G and remove the Platen Motor from
(3) Remove the Platen Motor with Motor Plate.
(4) Remove the 2 screws G and remove the Platen Motor from
the plate.
(1) Remove the Bottom Plate. (See
Bottom Plate
(
P.36
))
(2) Remove 2 screws E.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(3) Disconnect the connector on the CONTROL Board.
(4) Remove the FAN.
(1) Remove the Bottom Plate. (See
Bottom Plate
(
P.36
))
(2) Remove the 2 screws C.
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL board on the
(3) Remove the Power Supply.
(4) Disconnect the connector from the CONTROL board on the
Power Supply.
(1) Remove the Bottom Plate. (See
Bottom Plate
(
P.36
))
(2) Disconnect all connectors (7 cable connectors and 4 FFC
cables) to CONTROL Board.
(3) Remove the CONTROL Board
F
A
USB Earth Plate
Bottom Plate
C
Control Board
C
G
Platen Motor
Motor Plate
Power Supply
FAN
C
E
Control Board
Click on the first or last page to see other KV-S1057C / KV-S1027C / KV-SL1066 / KV-SL1056 / KV-SL1055 / KV-SL1036 / KV-SL1035 service manuals if exist.