Panasonic KV-S1025C / KV-S1020C Service Manual / Supplement ▷ View online
4
Note:
*1
: KV-S1025C Series
KV-S1025C: for USA
KV-S1025C-G: for Russia, etc.
KV-S1025C-U: for Europe
KV-S1025C-R: for Russia
KV-S1025C-K: for Korea
KV-S1025C-A: for Australlia
KV-S1025C-CN: for China
KV-S1025C-K: for Korea
KV-S1025C-A: for Australlia
KV-S1025C-CN: for China
KV-S1025C-T: for Taiwan
KV-S1025C-B: for Brazil
KV-S1025C-J: for GSA (made in Japan for USA)
KV-S1025C-J: for GSA (made in Japan for USA)
SERIAL No. shown on the name plate on each scanner will distinguish the destinations for each area as follows.
1. SERIAL No. for USA
→ 853 xxxx xxxx
2. SERIAL No.
for Russia, etc.
→ 858 xxxx xxxx
3. SERIAL No.
for Europe
→ 856 xxxx xxxx
4. SERIAL No. for Russia
→ 859 xxxx xxxx
5. SERIAL No. for Korea
→ 860 xxxx xxxx
6. SERIAL No. for Australlia
→ 857 xxxx xxxx
7. SERIAL No. for China
→ 861 xxxx xxxx
8. SERIAL No. for Taiwan
→ 862 xxxx xxxx
9. SERIAL No. for Brazil
→
D33 xxxx xxxx
10. SERIAL No. for GSA
→
C05 xxxx xxxx
(x: Don't care)
*2
: Applied to KV-S1025C for USA and other countries where power supply (AC100 to 120 V) is used
*3
: Applied to KV-S1025C-G/-U/-R/-K/-A/-CN/
-B/-GSA
for German, UK, Russia, Korea, Australlia, China,
Brazil,
and other
countries where power supply (AC220 to 240 V) is used.
*4
: The scanning speed depends on the test environment. In addition, it differs depending on the host computer operating
environment or applications.
*5
: MultiStream is registered trademark or trademark of EMC Corporation.
5
3 “SECTION 3 COMPONENT IDENTIFICATION”
Scanner status
Note: Stand-by Process
In the following cases, it will take 30 seconds to be able to scan.
Case 1: Just after power-on
Case 2: After about 2 hours pass by in the sleep mode
Case 3: After about 5 seconds or more pass by with ADF Door open
Case 1: Just after power-on
Case 2: After about 2 hours pass by in the sleep mode
Case 3: After about 5 seconds or more pass by with ADF Door open
LED
Scanner Status
Remarks
Green Red
ON
OFF
Ready
Blink (Slow)
OFF
Sleep
ON
Blink (Slow)
Caution
For cleaning or
replacing roller
replacing roller
Blink (Slow)
Blink (Slow)
Caution
in Sleep
For cleaning or
replacing roller
replacing roller
ON
ON
Error
Blink (Fast)
OFF
Warming Up
6
4 “SECTION 7 MAINTENANCE”
4.1.
“Section 7.1 Maintenance Chart”
C: Clean R: Replace
(x 1000 sheets)
Note 1:
The above roller maintenance values are registered in the maintenance counter (Refer to Section 9), and the PC will
inform users the cleaning or replacement timing if the utility software in this scanner has been already installed.
Note 2:
The maintenance schedule was determined according to paper standards (A4: 80 g/m
The maintenance schedule was determined according to paper standards (A4: 80 g/m
2
/ Letter: 20 lb.), which can
vary greatly between users. Therefore, the values can also vary.
Description
Part Reference No.
2
4
6
8-40
50
60
70
80
90
100
Paper Feed Roller
Ref. No. 85 in Sec. 14.1
C
C
C
Clean
each part
every 2
(x 1000)
sheets’
scanning.
C
C
C
C
C
R
Double-feed Prevention Roller
Ref. No. 40 in Sec. 14.1
C
C
C
C
C
C
C
C
R
Conveyor Roller
Ref. No. 87 in Sec. 14.1
C
C
C
C
C
C
C
C
C
Exit Roller
Ref. No. 96 in Sec. 14.1
C
C
C
C
C
C
C
C
C
Free Rollers
Ref. No. 28 in Sec. 14.1
C
C
C
C
C
C
C
C
C
Scanning Glass (F)
Ref. No. 34 in Sec. 14.1
C
C
C
C
C
C
C
C
C
Scanning Glass (B)
: KV-S1025C Series Only
: KV-S1025C Series Only
Ref. No. 111 in Sec. 14.1
C
C
C
C
C
C
C
C
C
7
4.2.
“Section 7.3 Replacing Limited Life Parts”
4.2.1.
“Section 7.3.1 Paper Feed Roller”
(1) Turn off the scanner by turning the Power Switch off and
unplugging the AC Adaptor from the scanner. (See 7.2.1.)
unplugging the AC Adaptor from the scanner. (See 7.2.1.)
(2) Remove the Feed Tray. (See 7.2.1.)
(3) Push the Door Open Button to open the ADF Door.
(See 7.2.1.)
(See 7.2.1.)
(4) After opening the Paper Feed Roller Cover, remove the
Paper Feed Roller.
Paper Feed Roller.
(5) Take out a new Paper Feed Roller from the Roller
Exchange Kit
Exchange Kit
(KV-SS035)
.
(6) Install the new Paper Feed Roller with its gear facing to the
left (seen from the back), and close the Paper Feed Roller
Cover.
left (seen from the back), and close the Paper Feed Roller
Cover.
Note:
Make sure to close the Paper Feed Roller Cover
tightly, by pressing both ends of the cover.
tightly, by pressing both ends of the cover.
(7) Close the ADF Door slowly until it clicks into place.
(See 7.2.3.)
(See 7.2.3.)
(8) After installing the Feed Tray, turn on the scanner by
plugging the AC Adaptor to the scanner and turning the
Power Switch on. (See 4.2 and 4.3.)
plugging the AC Adaptor to the scanner and turning the
Power Switch on. (See 4.2 and 4.3.)