Panasonic KV-S1025C / KV-S1020C (serv.man2) Service Manual / Supplement ▷ View online
5
2 “SECTION 1 GENERAL PRECAUTIONS”
2.1.
“Section 1.5 Standard for Repair Service”
Repair service shall be provided in accordance with repair technology information such as service manual
so as to prevent fires, injury or electric shock, which can be caused by improper repair work.
so as to prevent fires, injury or electric shock, which can be caused by improper repair work.
1. When performing repairs, neither the product nor its parts or components shall be modified.
2. If cable assembly is supplied as the smallest unit when servicing, make sure to replace
2. If cable assembly is supplied as the smallest unit when servicing, make sure to replace
the cable assembly.
6
3 “SECTION 3 COMPONENT IDENTIFICATION”
Scanner status
Note: Stand-by Process
In the following cases, it will take 30 seconds to be able to scan.
Case 1: Just after power-on
Case 2: After about 2 hours pass by in the sleep mode
Case 3: After about 5 seconds or more pass by with ADF Door open
Case 1: Just after power-on
Case 2: After about 2 hours pass by in the sleep mode
Case 3: After about 5 seconds or more pass by with ADF Door open
LED
Scanner Status
Remarks
Green Red
ON
OFF
Ready
Blink (Slow)
OFF
Sleep
ON
Blink (Slow)
Warning
For cleaning or
replacing roller
replacing roller
Blink (Slow)
Blink (Slow)
Warning in Sleep
For cleaning or
replacing roller
replacing roller
ON
ON
Error
Blink (Fast)
OFF
Warming Up
7
4 “SECTION 4 INSTALLATION”
4.1.
“Section 4.4 System Requirements”
Note 1
1.
The above system requirements may not meet the requirements of all operating systems and bundled
application software.
application software.
2. The scanning speed differs depending on the host computer’s operating environment or application.
3.
3.
If you connect the scanner to a USB hub, it is not guaranteed to work.
Note 2
1.
IBM and AT are trademarks of International Business Machines Corporation in the United States,
other countries, or both.
2. Windows
®
2000 is Microsoft
®
Windows
®
2000 operating system.
3. Windows
®
XP is Microsoft
®
Windows
®
XP operating system.
4.
Windows Vista
TM
is Microsoft
®
Windows Vista
TM
operating system.
5. Microsoft
®
, Windows
®
,
and Windows Vista
TM
are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries
6. Pentium is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States
7. Each company’s name or company product name is each company’s trademark or registered trademark.
7. Each company’s name or company product name is each company’s trademark or registered trademark.
Item
Contents
Computer
IBM PC/AT or compatible machine with a CD-ROM drive
CPU
Pentium 3, 1 GHz or higher
OS
Windows
®
2000, Windows
®
XP, Windows Vista
TM
(64 bit is not available.)
Interface
USB 2.0
Memory
256 MB or more
HDD
1 GB or more free space is required.
8
5 “SECTION 8 DISASSEMBLY INSTRUCTIONS”
5.1.
“Section 8.3 Mechanical Block”
5.1.1.
“Section 8.3.5 Optical Unit (F)”
(1) Remove the Rear Cover. (See 8.2.5.)
(2) Remove the CONTROL Board. (See 8.4.4.)
(3) Release the connector cables from the clamps inside and
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
(5) Remove the Base Plate, paying attention to the contact
between the cables and the plate edge.
between the cables and the plate edge.
(6) Remove the Ground (Earth) Plate 2.
(7) Release the cable from the clamp, and disconnect the CCD
Board (F) connector.
Board (F) connector.
(8) Remove the 2 screws.
(9) Remove the Optical Unit Covers FL and FR.
(Only for Product Version B or later)
(Only for Product Version B or later)
Click on the first or last page to see other KV-S1025C / KV-S1020C (serv.man2) service manuals if exist.