Panasonic KV-N1058X / KV-N1028X / KV-N1058Y / KV-N1028Y Service Manual ▷ View online
31
8.3.8.
Wiring of Upper Chassis
Hooked
Hooked
Insert
Insert
FG wire go though
the hole of core.
the hole of core.
With Auto/manual cable
Without Auto/manual cable
Push in these USB cables to
each slot.
each slot.
Bind these cables with "LEAD
BINDER " to Lowe Chassis.
BINDER " to Lowe Chassis.
Turn down the "LEAD BINDER "
as this photo.
as this photo.
32
8.4.
Lower Chassis 1
8.4.1.
Paper Feed Roller
8.4.2.
CIS (F)
(1) Remove the Paper Feed Roller Assembly.
(See Appendix
(
Operating Manual
P.107)
)
(2) Push the tab (arrow
1
) to remove the Feed Roller.
(3) Remove the rollers (arrow
2
) from the shaft.
Reassembling Note:
Make sure the left (white) and right (black) paper feed rollers
are installed correctly.
Make sure the left (white) and right (black) paper feed rollers
are installed correctly.
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Open the ADF Door.
(3) Remove screw C.
(3) Remove screw C.
(4) Unlock the 3 hooks.
(5) Remove the Scanning Glass (F).
(6) Take out the CIS(F) from the Main Unit.
(6) Take out the CIS(F) from the Main Unit.
White
Black
Feed Roller
2
1
2
2
Tab
C
Scanning Glass (F)
ADF Door
Hook
CIS (F)
Scanning Glass (F)
33
8.4.3.
Reference Plate (B)
8.4.4.
DOOR DETECTION Board
(1) Remove the CIS (F).
(See 8.4.2. CIS (F))
(2) Remove the Screw E.
(3) Remove the Spring.
(4) Remove the Slider in the direction of the arrows.
(3) Remove the Spring.
(4) Remove the Slider in the direction of the arrows.
Reassembling Note:
(1) Slider Gear Positioning.
Move the Slider Gear to the position where the gear
touches the rib.
touches the rib.
(2) Slider Positioning.
Insert the Slider into the Slider groove.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
With the position of the gear maintained, install the
Slider so that the Slider touches 2 ribs.
(5) Remove the Polyslider and the Reshuffling Lever.
(6) Remove the Reference Plate (B).
(6) Remove the Reference Plate (B).
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the DOOR DETECTION Board, while unlocking the
hook.
(3) Disconnect the connector.
Rib
Slider Gear Positioning
Slider Gear
Rib
Slider Positioning
Slider
Slider groove
E Spring
Slider
Reference Plate (B)
Reshuffling Lever
Polyslider
DOOR
DETECTION Board
DETECTION Board
Hook
34
8.4.5.
Side Plate Assembly
8.4.6.
Conveyor Roller
(1) Remove the Back Cover.
(See 8.2.5. Back Cover)
(2) Remove the screws A and the Earth Plate with the wire.
(3) Remove the 2 screws C and the Side Plate Assembly.
(3) Remove the 2 screws C and the Side Plate Assembly.
Reassembling Note:
a. When installing the Side-Plate Assembly, make sure to
position the Idle Pulley of the assembly.
Assemble the pulley to outside of the Conveyor Belt 2.
Assemble the pulley to outside of the Conveyor Belt 2.
b. After installing the Side-Plate Assembly, adjust the belt
tension as follows.
(1) Loosen Spring Plate Screw. (Proper belt tension will
(1) Loosen Spring Plate Screw. (Proper belt tension will
be adjusted by elastic force of the spring.)
(2) Tighten the screw. (See the right illustration.)
(1) Remove the Side Plate Assembly and Conveyor Belt 2.
(See 8.4.5. Side Plate Assembly)
(2) Pull the Pulley (arrow
2
), while unlocking the hook (arrow
1
)
and remove the Pulley.
Reassembling Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Conveyor Roller by pulling the Pulley.
Pulley is locked to the Conveyor Roller by pulling the Pulley.
(3) Slide and remove the bearing from the Conveyor Roller
(arrow
3
).
(4) Open and remove the Feed Roller Cover.
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
(5) Unlock the hook of the Conveyor Roller Bearing (arrow
4
)
(6) Unlock the Conveyor Roller by turning the Conveyor Roller
Bearing (arrow
5
),
(7) Slide the Conveyor Roller with the Conveyor Roller Bearing
(arrow
6
) and remove it (arrow
7
).
(8) Remove the Support Bearing.
(9) Remove the Polyslider.
(10) Remove the Conveyor Roller Bearing from the Conveyor
(10) Remove the Conveyor Roller Bearing from the Conveyor
Roller.
Idle Pulley
Conveyor Belt 2
tension
C
A
Earth Plate
Side Plate Assembly
C
Spring Plate Screw
Bearing
Pulley
Conveyor
Roller
Roller
Hook
1
2
3
Feed Roller
Cover
Cover
Conveyor Roller
Conveyor
Roller
Bearing
Roller
Bearing
Support
Bearing
Bearing
4
6
5
7
Conveyor Roller Bearing
Support Bearing
Polyslider
Click on the first or last page to see other KV-N1058X / KV-N1028X / KV-N1058Y / KV-N1028Y service manuals if exist.