Panasonic NV-GS50EG / NV-GS50EGM / NV-GS50B / NV-GS50EN / NV-GS50A / NV-GS50ENT / NV-GS40EG / NV-GS40EGM / NV-GS40B / NV-GS30EG / NV-GS30EGE / NV-GS30EGM / NV-GS30B / NV-GS30EN / NV-GS30A / NV-GS30ENT / NV-GS10EG / NV-GS10EGE / NV-GS10EGM / NV-GS10B (serv.man2) Service Manual ▷ View online
2003
NV-GS50EG
NV-GS50EGM
NV-GS50B
NV-GS50EN
NV-GS50A
NV-GS50ENT
NV-GS40EG
NV-GS40EGM
NV-GS40B
NV-GS30EG
NV-GS30EGE
NV-GS30EGM
NV-GS30B
NV-GS30EN
NV-GS30A
NV-GS30ENT
NV-GS10EG
NV-GS10EGE
NV-GS10EGM
NV-GS10B
NV-GS50B
NV-GS50EN
NV-GS50A
NV-GS50ENT
NV-GS40EG
NV-GS40EGM
NV-GS40B
NV-GS30EG
NV-GS30EGE
NV-GS30EGM
NV-GS30B
NV-GS30EN
NV-GS30A
NV-GS30ENT
NV-GS10EG
NV-GS10EGE
NV-GS10EGM
NV-GS10B
VOL.2
Q3-MECHANISM
Colour
(S)..........Silver Type
(A)..........Blue Type (only NV-GS10)
(R)..........Red Type (only NV-GS10)
Digital Video Camera/Recorder
ORDER NO.VM0302017C8
2
NV-GS50EG
1
INTRODUCTION
4
1.1.
INTRODUCTION
4
1.2.
ABOUT LEAD FREE SOLDER (PbF)
4
2
SERVICE CAUTION
5
2.1.
SERVICE EXTENSION CABLE FOR ALL C.B.A.
INCLUDED IN MODULE UNIT
5
3
BLOCK DIAGRAMS
7
3.1.
CAMERA/LENS DRIVE BLOCK DIAGRAM
7
3.2.
CONTROL 1 BLOCK DIAGRAM
8
3.3.
CONTROL 2 BLOCK DIAGRAM
9
3.4.
VIDEO BLOCK DIAGRAM
10
3.5.
DSC BLOCK DIAGRAM (NV-GS50, GS40,
GS30EN/ENT/A ONLY)
11
3.6.
MONITOR BLOCK DIAGRAM
12
4
SCHEMATIC DIAGRAMS
13
4.1.
SUB CONNECTION SCHEMATIC DIAGRAM
13
4.2.
EX INPUT SCHEMATIC DIAGRAM (NV-GS50, GS40,
GS30EN/ENT/A ONLY)
14
4.3.
DSC MPEG SCHEMATIC DIAGRAM
16
4.4.
MAIN CONNECTION SCHEMATIC DIAGRAM
20
4.5.
MIC/ IR SCHEMATIC DIAGRAM
23
4.6.
CAMERA SCHEMATIC DIAGRAM
24
4.7.
LENS DRIVE SCHEMATIC DIAGRAM
25
4.8.
LCD SCHEMATIC DIAGRAM
26
4.9.
HEAD/REC AMP SCHEMATIC DIAGRAM
27
4.10. VIDEO 2 SCHEMATIC DIAGRAM
28
4.11. VIDEO 1 SCHEMATIC DIAGRAM
30
4.12. POWER SCHEMATIC DIAGRAM
33
4.13. DRIVE SCHEMATIC DIAGRAM
35
4.14. CONTROL SCHEMATIC DIAGRAM
36
5
CIRCUIT BOARD ASSEMBLIES
43
5.1.
MAIN C.B.A. (COMPONENT SIDE)
43
5.2.
MAIN C.B.A. (FOIL SIDE)
44
5.3.
MAIN C.B.A. ADDRESS INFORMATION
45
5.4.
SUB C.B.A. (NV-GS50, GS40, GS30EN/ENT/A ONLY) 46
6
CHECKING POINT OF THE CSP IC
49
6.1.
CHECKING POINT TABLE
49
6.2.
WAVEFORM TABLE (PLAY MODE)
63
7
REPLACEMENT PARTS LIST
69
7.1.
ELECTRICAL PARTS LIST
69
CONTENTS
Page
Page
3
NV-GS50EG
1 INTRODUCTION
1.1. INTRODUCTION
This service manual contains technical information which will allow service personnel´s to understand and service this
model.Please place orders using the parts list and not the drawing reference numbers.
model.Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
manual.
Note 1:
These movie camera is used Q-Mechanism.
Disassembly, Assembly and Adjustment Procedures for Mechanism Chassis separated volume.
Information for Q-Mechanism should be referd to the another manual as below.
Order No. : VMD0109026C8
1.2. ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PdF stamp on the PCB.
Caution:
·
Pb free solder has a higher melting point than standard solder, Typically the melting point is 50-70°F (30-40°C) higher.
Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700±20°F
(370±10°C).
(370±10°C).
·
Pb free solder will tend to splash when heated too high (about 1100°F/ 600°C).
When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the
soldering points with the Pb free solder until it melts enough.
soldering points with the Pb free solder until it melts enough.
4
NV-GS50EG
