Panasonic NV-DS60EG / NV-DS60EGE / NV-DS60EGM / NV-DS60B / NV-DS60EN / NV-DS60ENT / NV-DS60ENC / NV-DS60A / NV-DS65EG / NV-DS65EGE / NV-DS65EGM / NV-DS65B / NV-DS65EN / NV-DS65ENT / NV-DS65ENC / NV-DS65A (serv.man2) Service Manual ▷ View online
2003
NV-DS60EG NV-DS60EGE
NV-DS60EGM NV-DS60B
NV-DS60EN NV-DS60ENT
NV-DS60ENC NV-DS60A
NV-DS65EG NV-DS65EGE
NV-DS65EGM NV-DS65B
NV-DS65EN NV-DS65ENT
NV-DS65ENC NV-DS65A
NV-DS60EN NV-DS60ENT
NV-DS60ENC NV-DS60A
NV-DS65EG NV-DS65EGE
NV-DS65EGM NV-DS65B
NV-DS65EN NV-DS65ENT
NV-DS65ENC NV-DS65A
Vol. 2
Colours
(S)...................Silver Type
Digital Video Camcorder
ORDER NO. VM0301007C8
1
INTRODUCTION
3
1.1.
INTRODUCTION
3
2
ABOUT LEAD FREE SOLDER (PbF)
3
3
SERVICE NOTES (PLEASE READ)
4
3.1.
SERVICE NOTES
4
4
SCHEMATIC DIAGRAMS
9
4.1.
SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT
NOTES
9
4.2.
MAIN SCHEMATIC DIAGRAMS (Models: NV-DS60EG-
S/EGM-S/B-S/EGE-S/EN-S/ENT-S/ENC-S/A-S)
10
4.3.
MAIN SCHEMATIC DIAGRAMS (Models: NV-DS65EG-
S/EGM-S/B-S/EGE-S/EN-S/ENT-S/ENC-S/A-S)
27
4.4.
VOLTAGE CHART
46
5
CIRCUIT BOARD LAYOUT
49
5.1.
MAIN C.B.A. (Models: NV-DS60EG-S/EGM-S/B-S/EGE-
S/EN-S/ENT-S/ENC-S/A-S)
49
5.2.
MAIN C.B.A. (Models: NV-DS65EG-S/EGM-S/B-S/EGE-
S/EN-S/ENT-S/ENC-S/A-S)
51
6
REPLACEMENT PARTS LISTS
53
6.1.
REPLACEMENT NOTES
53
6.2.
ELECTRICAL REPLACEMENT PARTS LIST
54
CONTENTS
Page
Page
2
NV-DS60EG NV-DS60EGE
1 INTRODUCTION
1.1. INTRODUCTION
This service manual contains technical information which will
allow service personnel´s to understand and service this model.
Please place orders using the parts list and not the drawing
reference numbers.
allow service personnel´s to understand and service this model.
Please place orders using the parts list and not the drawing
reference numbers.
If the circuit is changed or modified, this information will be
followed by supplement service manual to be filed with original
service manual.
followed by supplement service manual to be filed with original
service manual.
2 ABOUT LEAD FREE
SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
stamp on the PCB.
Caution:
·
Pb free solder has a higher melting point than standard
solder; Typically the melting point is 50-70°F (30-40°C)
higher.
solder; Typically the melting point is 50-70°F (30-40°C)
higher.
Please use a high temperature soldering iron. In case of
thesoldering iron with temperature control, please set it
to 700±20°F (370±10°C).
thesoldering iron with temperature control, please set it
to 700±20°F (370±10°C).
·
Pb free solder will tend to splash when heated too high
(about 1100°F/600°C).
(about 1100°F/600°C).
When soldering or unsoldering, please completely remove all
of the solder on the pins or solder area, and be sure to heat the
soldering points with the Pb free solder until it melts enough.
of the solder on the pins or solder area, and be sure to heat the
soldering points with the Pb free solder until it melts enough.
3
NV-DS60EG NV-DS60EGE
3 SERVICE NOTES (PLEASE READ)
3.1. SERVICE NOTES
3.1.1. EXTENSION CABLES FOR SERVICE POSITION
Using the following Extension Cables, place the unit as shown for check and service.
Note :
1. The LCD open/close SW. is for changing between LCD Display or EVF Display. When turning on LCD Display, place some
paper or tape, etc. on LCD open/close SW. so that this SW. stays ON.
2. Connect the F.P.C.s to the connectors, verifying the direction of F.P.C. as shown.
3. Use a grounded ESD wrist strap while disassembling the Lens portion.
4. Use extreme care when unplugging or plugging in connectors.
4
NV-DS60EG NV-DS60EGE
