DOWNLOAD Panasonic HDC-HS900P / HDC-HS900PC / HDC-HS900PU / HDC-HS900EB / HDC-HS900EEK / HDC-HS900EG / HDC-HS900EP / HDC-HS900GC / HDC-HS900GN / HDC-HS900GT / HDC-HS900GK Service Manual ↓ Size: 8.29 MB | Pages: 101 in PDF or view online for FREE

Model
HDC-HS900P HDC-HS900PC HDC-HS900PU HDC-HS900EB HDC-HS900EEK HDC-HS900EG HDC-HS900EP HDC-HS900GC HDC-HS900GN HDC-HS900GT HDC-HS900GK
Pages
101
Size
8.29 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie / HIGH DEFINITION VIDEO CAMERA
File
hdc-hs900p-hdc-hs900pc-hdc-hs900pu-hdc-hs900eb-hdc.pdf
Date

Panasonic HDC-HS900P / HDC-HS900PC / HDC-HS900PU / HDC-HS900EB / HDC-HS900EEK / HDC-HS900EG / HDC-HS900EP / HDC-HS900GC / HDC-HS900GN / HDC-HS900GT / HDC-HS900GK Service Manual ▷ View online

6
2.3.
Caution for AC Cord 
(For EB/GC)
2.3.1.
Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
 DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2.
Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1.
Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2.
Before Use
Remove the Connector Cover as follows.
2.3.2.3.
How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue
Neutral
Brown
Live
7
2.4.
How to Replace the Lithium Battery
2.4.1.
Replacement Procedure
1. Remove the MIC AMP P.C.B.. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B6401” at component side of MIC AMP P.C.B.) and then replace it into new one.
NOTE:
This Lithium battery is a critical component. 
(Type No.: ML-614S/ZTK Manufactured by Energy Company, Panasonic Corporation)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for HDC-HS900 series, as well.
1. Battery Pack for this model.
8
3 Service Navigation
3.1.
Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2.
General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30
°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30
°C
(662±86
°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3.
Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servicing at component level
without concerned equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B..
b. Parts list for individual parts for MAIN P.C.B..
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.)
2. The following category is /are recycle module part. Please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP03J06CN: HDC-HS900P/PC/PU/GT)
• MAIN P.C.B. (VEP03J06CP: HDC-HS900EB/EG/EP)
• MAIN P.C.B. (VEP03J06CQ: HDC-HS900EE/GC/GK/GN)
9
3.4.
How to Define the Model Suffix (NTSC or PAL model)
There are six kinds of HDC-HS900.
• a) HDC-HS900P
• b) HDC-HS900PC
• c) HDC-HS900EB/EG/EP/GN
• d) HDC-HS900EE
• e) HDC-HS900GK
• f) HDC-HS900GC/PU
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..
3.4.1.
Defining methods:
To define the model suffix to be serviced, refer to the rating label  and caution label which are putted on the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
Page of 101
Display

Click on the first or last page to see other HDC-HS900P / HDC-HS900PC / HDC-HS900PU / HDC-HS900EB / HDC-HS900EEK / HDC-HS900EG / HDC-HS900EP / HDC-HS900GC / HDC-HS900GN / HDC-HS900GT / HDC-HS900GK service manuals if exist.