DOWNLOAD Panasonic HC-V10EE Service Manual ↓ Size: 4.46 MB | Pages: 59 in PDF or view online for FREE

ORDER NO. VM1202004CE

B27

Colour
[ HC-V10 ]
(K)...........Black Type
(R)...........Red Type (except PC/EF/GK/GN/GT/GW)
(S)...........Silver Type (only P/GA/GC/GK/GN)
[ HC-V10M / HC-V11M ]
(K)...........Black Type

2

PAGE

PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3

2 Warning --------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------4

2.2. How to Recycle the Lithium Ion Battery (U.S.

Only)-----------------------------------------------------------4

2.3. How to Replace the Lithium Battery-------------------5

3 Service Navigation------------------------------------------------6

3.1. Introduction --------------------------------------------------6
3.2. General Description About Lead Free Solder

(PbF) ----------------------------------------------------------6

3.3. Important Notice 1:(Other than U.S.A. and

Canadian Market) ------------------------------------------6

3.4. How to Define the Model Suffix (NTSC or PAL

model)---------------------------------------------------------7

3.5. Formatting----------------------------------------------------8

4 Specifications ------------------------------------------------------9
5 Location of Controls and Components------------------ 11
6 Service Mode ----------------------------------------------------- 13

6.1. History Display -------------------------------------------- 14

7 Service Fixture & Tools --------------------------------------- 15

7.1. When Replacing the Main P.C.B. -------------------- 15
7.2. Service Position ------------------------------------------ 15

8 Disassembly and Assembly Instructions--------------- 16

8.1. Disassembly Flow Chart for the Unit ---------------- 16
8.2. PCB Location---------------------------------------------- 16
8.3. Disassembly Procedure for the Unit ---------------- 17

9 Measurements and Adjustments -------------------------- 24

9.1. Electric Adjustment -------------------------------------- 24

10 Factory Setting--------------------------------------------------- 26

10.1. How To Turn On The Factory Settings? ------------ 26
10.2. What Is The Factory Settings? ----------------------- 26

11 Block Diagram --------------------------------------------------- 27

11.1. Overall Block Diagram ---------------------------------- 27
11.2. Camera/System Control Circuit Block

Diagram----------------------------------------------------- 28

11.3. Video/Audio Signal Process Circuit Block

Diagram----------------------------------------------------- 29

11.4. Lens Drive Circuit Block Diagram-------------------- 30
11.5. Power Supply Circuit Block Diagram---------------- 31

12 Wiring Connection Diagram --------------------------------- 32

12.1. Interconnection Diagram ------------------------------- 32

3

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment
which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.

2. An Isolation Transformer should always be used during

the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices

such as insulation barriers, insulation papers shields are
properly installed.

5. After servicing, make the following leakage current

checks to prevent the customer from being exposed to
shock hazards.

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M

Ω and 5.2 MΩ. When the exposed

metal does not have a return path to the chassis, the
reading must be infinity.

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5 k

Ω, 10 W resistor, in parallel with a 0.15 μF

capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 k

Ω/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.

Figure. 1

4

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.
CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).