Panasonic NR-D513XB-S8 / NR-D513XR-S8 Service Manual ▷ View online
5. Disassembly and Assmbly Instructions
5.1 FCC SENSOR
5.2 THERMAL FUSE, DFC SENSOR, d.c FAN MOTOR
‧Take out the FC bottom case & top case.
DEFROST HEATER
‧Remove the screw(1 pcs)which fix the ice corner AS.
‧Take out the VC top case & bottom case.
‧Pull the ice corner AS.
‧Take out the ice corner AS.
‧Remove the screw(1 pcs)which fix the plate duct FC. & pull it.
‧Take out the FC top case & bottom case.
‧Take out the ice corner AS.
‧Remove the screw(1 pcs)which fix the cover coil AS.
‧Pull down the cover coil AS.
‧Pull the ice corner AS. toward you to remove.
‧Unhook FCC SENSOR of cord.
‧Each part is installed as shown in the figure.
CAUTION
To replace the FCC SENSOR
‧FCC SENSOR of cord
should be hooked in plate.
‧Pull the DFC SENSOR to the direction of arrow.
‧Cut binding tubeand remove thermal fuse.
To replace thermal fuse
‧Be sure to put themal fuse in place.
‧Bind lead wire without loose as shown in the figure.
Screw
FCC SENSOR
plate duct FC
Screw
Screw
Cover coil &
Fan Motor AS.
Thermo. fuse
DFC SENSOR
Defrost heater
Top case
Bottom case
Binding tube
Thermal fuse
Binding tube
-12-
5.3 DC FAN MOTOR
(DEFROST HEATER)
‧Disconnect the terminal (1 pcs).
‧Remove the cover coil & fan motor as.
‧Remove the crape tape which set the ins. cover coil front
‧Lifting the evaporator at right gradually, pull it toward you.
& cover coil.
NOTE :
‧Remove the crape tape which set the ins. cover coil front
Special care should be taken not to twist and break the pipe.
& back.
‧Remove the crape tape which set the DC FAN MOTOR
of cord.
To replace the DC fan motor
‧Insert the DC fan motor case into the ins. cover coil back.
‧Connect the terminal.
Cover coil
ins. cover
coil front
Crape tape
ins. cover
coil back
Connector
DC Fan motor
Crape tape
Heater holder
Heater cover
Edge
Defrost heater
Evaporator
Lead wire
Heater holder
Defrost heater
Heater cover
Hook for lead wire
-13-
5.4 BIO FAN MOTOR & DAMPER THERMOSTAT
‧Remove lamp cover.
‧Tear off the tapes on insulation.
‧Remove screws(3 pcs), and pull out the
Open the insulation from the front side pull the upper portion.
control panel AS. toward you.
‧Remove the damper thermostat from insulation.
‧Disconnect the terminal.
‧Disconnect the ins. control panel AS. & control panel.
To replace damper thermo.
‧Sealing dial should be put in place.
‧Seal the gap between the front insulation and the back insulation
by putting tape.
‧Hook the sensor bulb in place.
‧Remove the thermostat dial.
Screw
Control panel AS.
Ins.control panel AS.
Damper thermo.
Control panel
Ins. Control panel front
Ins. Control panel back
-14-
5.5 STARTING RELAY & OVERLOAD PROTECTOR
‧
Remove the screws(5pcs) which are fixed on comp.
‧
Pull the starting relay leftwards to remove.
cover.
To replace starting relay
‧Remove the comp. cover.
‧Insert the starting relay into comp. pin.
‧Remove the relay cover than pull out overload protector.
‧Install the protector into relay cover.
‧Pushing the protector cover into comp.
‧
Pull the starting relay leftwards to remove.
5.6 Caution in shipping
Service personnel should be careful not to crush the COMP COVER
when moving the refrigerator.
Deformation may happen when crusing the cover.
※ If a trolley is used for moving the refrigerator,
move the refrigerator on its side.
REFRIGERANT FLOW DIAGRAM
‧Refrigerant flows in the refrigerating units as shown in the figure.
‧Number in the figure of " PIPE LAYOUT " corresponds to number in the refrigerant flow diagram.
Starting relay
①
②
③ ⑤
Bottom Condenser
⑥
⑦
Front Condenser
Side Condenser
⑧
⑨
Comp.
Evaporator
Dryer
④
Screw
Screw
SIDE
COMP COVER
COMP COVER
Relay cover
Overload protector
-15-
Click on the first or last page to see other NR-D513XB-S8 / NR-D513XR-S8 service manuals if exist.