Panasonic MC-E3011 Service Manual ▷ View online
Ref. No.
Part No.
Part Name & Description
Q’TY
Remarks
65
AMC97R-ZS00E
Floor nozzle lower unit
1
66
AMC42D-XB00E
Bolt A
1
68
AMC50R-XD00E
Floor nozzle roller shaft
2
69
AMC90Q-XD00E
Nozzle roller
2
72
XWG7F135FJ
Plain washer
2
73
AMC95S-XD00E
Belt Kit Assy
1
74
AMC28S-XD00E
Belt
1
75
AMC39S-XD00E
Belt B
1
76
AMC92S-XD00E
Beater bar unit
1
77
AMC28H-XB00E
Elbow packing
1
78
AMC04Z-XD00E
Sticker
1
79
XTN4+18BFJ
Tapping screw
16
80
DS-250PU
Insulation tube
1
5
MC-E3011
1. Loosen 5 screws from the base plate (Floor nozzle lower
unit) and remove it.
(Fig. 1)
(Fig. 1)
2. Remove the beater bar unit from the floor nozzle upper unit.
(Fig. 2)
3. Remove the 1 screw from the pedal shaft to detach the
pedal. (Fig. 3)
4. Pull out the pedal shaft slightly. Remove the tip of the shaft
from the metal plated of the idler pulley. Then remove it
together with the pedal.
together with the pedal.
5. Remove belt B from the motor shaft and then from the idler
pulley.
6. Remove the belt from the beater bar unit and then from the
idler pulley.
7. Fit a new belt and belt B by reversing the disassembly
procedure. Fit the belt first, then belt B.
4 REPLACEMENT OF MAIN PARTS
IMPORTANT: Before replacing any part always DISCONNECT THE CLEANER FROM THE ELECTRICITY SUPPLY.
4.1. BELT (Beater bar belt), BELT B (Motor shaft belt)
6
MC-E3011
1. Remove the base plate (floor nozzle lower unit).
2. Remove the beater bar unit from the floor nozzle upper unit.
(Fig. 4)
3. Replace the ber unit with a new and place the belt around
the beater bar unit. (fig. 5)
4. Insert the beater bar unit in the groove of the floor nozzle
upper unit. Rotate the beater bar unit by hand and check
that it is fitted properly.
that it is fitted properly.
5. Replace the base plate (Floor nozzle lower unit) and
refasten screw.
1. Remove the base plate. (Floor nozzle lower unit)
2. Remove 1 screw from the pedal and take it out. (Fig. 5).
3. Release the two belts from the Idler pulley.
4. Remove 2 screws from the Idler pulley unit and take it out.
(Fig. 6)
5. Replace the Idler pulley unit with a new one and re-install it.
6. Re-assemble the pedal, belts and remaining parts in the
reverse order.
4.2. BEATER BAR UNIT
4.3. IDLER PULLEY UNlT
7
MC-E3011
1. As described in paragraph 4.3 of "IDLER PULLEY UNlT",
remove the base plate (floor nozzle lower unit), pedal, and
idler pulley, and belt B, belt.
idler pulley, and belt B, belt.
2. Disconnect the hose and connector pipe from the floor
nozzle upper unit (Fig.7).
3. Insert a flat-head screwdriver between nozzle housing and
the plastic holder, then pry out the plastic holder. (Fig.8).
4. Turn the vacuum cleaner over and remove 4 screws from
Moter case and take it out. (Fig.9)
* Connection of lead wire A unit during assembly
Connect lead wire A unit as shown in Fig. 9-1.
4.4. FAN MOTOR UNIT
8
MC-E3011
Click on the first or last page to see other MC-E3011 service manuals if exist.