Panasonic ES8243 Service Manual ▷ View online
5
4 Disassembly and Assembly Instructions
4.1.
Disassembly Instructions
Follow the procedure below to disassemble the main unit.
1. Remove the cap, the outer foil and the inner blade.
2. How to disassemble the housing A and B.
a. Loosen a screw.
b. Remove the bottom cover.
b. Remove the bottom cover.
c. Slide the trimmer handle up.
d. Loosen a screw.
e. Slide the trimmer handle down.
e. Slide the trimmer handle down.
f. Remove the trimmer sliding downward.
g. Remove the upper rear panel.
h. Loosen two screws.
h. Loosen two screws.
i. Remove the rear panel
j. Loosen six screws.
j. Loosen six screws.
k. Remove the housing B.
3. Remove the finishing blade driving bar by moving one
side of the bar as show the arrow. To remove the trimmer
driving bar, press bars outward. Remove the slit blade
driving bar by moving one side of the bar as show the
arrow.
driving bar, press bars outward. Remove the slit blade
driving bar by moving one side of the bar as show the
arrow.
4. Pull up the battery and chassis block from the linear
motor side first. Then, slide it upward and take it out from
the housing A.
NOTE:
the housing A.
NOTE:
Do not pull the battery and chassis block forcefully
due to connecting the linear motor by the lead wires.
due to connecting the linear motor by the lead wires.
6
5. Take out the battery from the chassis.
6. Take out the tube holder.
7. Move gently the linear motor assembly down and unhook
it and remove the float springs from housing A.
8. Unsolder the lead wires from the module.
7
4.2.
Caution in Assembly
NOTE:
When reassembling, replace the new waterproof seal. Make sure whether there is NO foreign substance sticking around a part
covered with waterproof seal.
covered with waterproof seal.
1. Solder the lead wires with the module.
NOTE:
Make sure of the color of lead wires.
2. When inserting the module and chassis block into the
housing A, confirm if the module does not get any dam-
age or deformation.
age or deformation.
3. Make sure that the lead wires set in position to avoid
abnormal noise. Install (+) terminal of battery into the ter-
minal plate at the bottom cover side and firmly set the bat-
tery sliding the direction of arrow. Attach (-) terminal of
battery.
NOTE:
minal plate at the bottom cover side and firmly set the bat-
tery sliding the direction of arrow. Attach (-) terminal of
battery.
NOTE:
Once taking the battery out, the shaver is RESET.
The shaver must be charged for several seconds first.
The shaver must be charged for several seconds first.
NOTE:
Completely discharge and then fully charge before
returning the shaver to the customer.
returning the shaver to the customer.
8
4. Set the linear motor assembly on the housing A and slid-
ing it upward to hook. Confirm that the lead wire tube fits
to the housing A firmly and no foreign substance sticking
around. Attach the tube holder with the lock lever shaft to
housing A with care of the direction.
to the housing A firmly and no foreign substance sticking
around. Attach the tube holder with the lock lever shaft to
housing A with care of the direction.
5. When putting the housing A and the housing B together,
make sure if the waterproof seal must be fitted properly
and no foreign substance sticking around.
and no foreign substance sticking around.
6. Tighten six screws.
NOTE:
Make sure to attach the connecting plate.
7. Insert two hooks on top of the rear panel into the dent of
housing first and attach the rear panel firmly. Set the rear
panel with the position “LOCK”.
NOTE:
panel with the position “LOCK”.
NOTE:
Make sure of the smooth movement of the lock lever
shaft.
shaft.
Click on the first or last page to see other ES8243 service manuals if exist.