Panasonic ES-LL21 / ES-LL41-K520 Service Manual ▷ View online
ES-LL21/LL41
5
4. DISASSEMBLY/ASSEMBLY INSTRUCTIONS
Water-washing type. Use caution for the following
points.
points.
1. When repairing a circuit base assembly, check the O-ring
"not caught in another part", "position shifted", or "no
adhering dust".
adhering dust".
2. When combining a body block and linear motor, check the
O-ring "not caught in another part", "position shifted", or
"dust attachment".
"dust attachment".
4.1Disassembly instructions
Follow the procedure below to disassemble the
body block.
body block.
1. Remove the cap, the outer foil with outer foil frame and
the inner blades.
2.Method of removing the trimmer handle.
a. Lift the trimmer block.
b. Remove the trimmer handle by disengaging the two
b. Remove the trimmer handle by disengaging the two
hooks on the trimmer handle and from the two holes
in the trimmer block.
in the trimmer block.
3.Remove the trimmer from the two hooks.
ES-LL21/LL41
6
4.How to disassemble the back panel set and real panel.
a. Loosen a screw and remove the real panel.
b. Pry the back panel.
c. Remove the back panel.
d. Loosen 8 screws .
e. Remove the housing B .
c. Remove the back panel.
d. Loosen 8 screws .
e. Remove the housing B .
5. Remove the slit blade driving bar and trimmer driving bar .
6.Method of removing the module from the housing A.
7.Take out the battery from the module.
Note : Use caution not to lose the O-rings .
8.Unsolder the lead wires from the module.
(Pay attention to the temperature is not too high.)
ES-LL21/LL41
7
9.Loosen 2 screws from housing A and pull up
the motor.
4.2Caution in
assembly
assembly
1. Solder the lead wires with the module.
(A red-marked lead wire is connected to the terminal
indicating "Red" on the circuit board.)
indicating "Red" on the circuit board.)
2. Install (+) terminal of battery into the terminal plate at the
bottom cover side and firmly set the battery slide in the
direction of arrow. Attach (-) terminal of battery.
direction of arrow. Attach (-) terminal of battery.
Use caution for the insertion direction, of the storage
battery, either (+) or (-).
*After assembly, rotate the battery 180° and/or 90° in the
position to check (+) marking on the battery is in the right
direction.
battery, either (+) or (-).
*After assembly, rotate the battery 180° and/or 90° in the
position to check (+) marking on the battery is in the right
direction.
3 .Method of attach the module into the housing A.
a. The charging terminal aligns with the housing A hole
position.
b. Attach the module into the housing A .
ES-LL21/LL41
8
4. Make sure that lead wires should be sagging . Twist the lead wires
in half round and allocate them between housing ribs.
5.Method of attach the motor into the housing A by using 2 screws.
6.
Make sure the slit blade driving bar and trimmer driving bar are
in the right direction .
in the right direction .
7. Assembly of the back panel and real panel set.
a. Attach the housing B into the body block .
b. Attach 8 screws into housing B.
c.
b. Attach 8 screws into housing B.
c.
Attach the back panel into the body block.
d. Make sure the back panel is in place.
e. Attach the real panel into the body block by using a
e. Attach the real panel into the body block by using a
screw .
8. Assembly of the trimmer and trimmer handle.
• Engage the two hooks of the trimmer handle with the two
holes in the trimmer, and engage the two hooks of the
trimmer handle with the body block.
trimmer handle with the body block.
• Engage trimmer with the two hooks of the body block .
Click on the first or last page to see other ES-LL21 / ES-LL41-K520 service manuals if exist.