Panasonic KX-TU301RUME Service Manual ▷ View online
5
KX-TU301RUME
2.2.1.
Suggested PbF Solder
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
2.3.
Discarding of P.C.Board
When discarding P.C.Board, delete all personal information such as telephone directory and caller list of scrap P.C.Board.
0.3 mm X 100 g
0.6 mm X 100 g
1.0 mm X 100 g
6
KX-TU301RUME
3 Specifications
Note:
• Design and specifications are subject to change without notice.
Standard:
Frequency band:
Tx Frequency range:
Rx Frequency range:
Tx / Rx separation:
Number of RF channels:
Output power:
Duplex procedure:
Channel spacing:
Bit rate:
Modulation:
Connection:
Frequency band:
Tx Frequency range:
Rx Frequency range:
Tx / Rx separation:
Number of RF channels:
Output power:
Duplex procedure:
Channel spacing:
Bit rate:
Modulation:
Connection:
Audio:
SIM card type:
Power source:
Power source:
Dual-band GSM 900/1800 MHz
45 MHz
174
174
95 MHz
374
374
FDD - TDMA (Frequency Division Duplex - Time Division Multiple Access
200 kHz
270.833 kbit/s
GMSK (Gaussian filtered Minimum Shift Keying)
8 Ch/TDMA
200 kHz
270.833 kbit/s
GMSK (Gaussian filtered Minimum Shift Keying)
8 Ch/TDMA
Battery:
Li-Ion 3.7 V/940 mAh
Antenna:
Internal
1.8 V/3 V
Half Rate, Full Rate, Enhanced Full Rate (HR/FR/EFR)
Adaptive Multi-rate - Narrow Band (AMR-NB)
Adaptive Multi-rate - Narrow Band (AMR-NB)
900 MHz EGSM 900
1800 MHz DCS 1800
880-915 MHz
1,710 - 1,785 MHz
925 - 960 MHz
1,805 - 1,880 MHz
Class 4 (2W)
Class 1 (1W)
Power consumption(Charger):
Operating/Charging conditions:
Dimensions(Charger):
Dimensions(Handset):
Mass(weight)(Charger):
Mass(weight)(Handset):
Dimensions(Charger):
Dimensions(Handset):
Mass(weight)(Charger):
Mass(weight)(Handset):
220-240 V AC, 50/60 Hz
Standby: Approx. 0.2 W
Maximum: Approx. 4.0 W
Standby: Approx. 0.2 W
Maximum: Approx. 4.0 W
0
°C–40°C, 20%–80% relative air humidity (dry) Charging: 5 ˚C – 40 ˚C
Approx. 63 mm x 68 mm x 45 mm
Approx. 49 mm x 20 mm x 128 mm
Approx. 50 g
Approx. 130 g
Approx. 49 mm x 20 mm x 128 mm
Approx. 50 g
Approx. 130 g
7
KX-TU301RUME
4 Technical Descriptions
4.1.
Block Diagram (Handset)
FLASH
IC2
32M bit
26MHz
Crystal
X1
Crystal
X1
32KHz
Crystal
X2
Crystal
X2
TFT-LCD
(128 x160)
(128 x160)
POW
Jack
Litium-ion
Battery
Battery
KeyPAD
Key
LED
LED
LCD LED
SIM Card
GSM Module
MOD1
SRAM
IC3
1M bit
MIC
RECEIVER
SPEAKER
SPI
BACKLIGHT
KEY
SIM
16bit
16bit
VBAT
POWON SW
PWON
Headset Jack
LED
Power IC (IC3)
Power IC (IC3)
W_LED_DRV
Tx Module
(PA+SW)
Rx
SAW
Matching
Matching
Antenna
Tx (900)
Tx (1800)
Rx(900)
Rx(1800)
PMB7880 (ULC2)
MIC
EPP
SP
HS_MIC
Torch
LED
LED
Charger
Control
IC (IC2)
Control
IC (IC2)
LDO
IC1
IC1
KeyLock SW
KeyLock
Vibrator
LDO
IC4
IC4
VIB
Charger
Termina
Termina
AC Adapter
(PNLV226)
(PNLV226)
CHARGER
Thermistor
CF1
CF1
M0
Bell
LED
LED
HS_SP
HS_DET
(M2)
(M2)
7 11
6
15
41
17 26
29 32
28
53
63
34
44
39,40
46,47
35,36,58,59
48,49
2 4,52
KX-TU301 BLOCK DIAGRAM (HANDSET)
8
KX-TU301RUME
4.2.
Circuit Operation (Handset)
4.2.1.
Outline
Handset consists of the following ICs as shown in Block Diagram (Handset) (P.7).
• GSM Module : MOD1
- GSM (GSM900/DCS1800) Network interface
- GSM Audio
- GSM Audio
Half Rate, Full Rate, Enhanced Full Rate (HR/FR/EFR),
Adaptive Multi-rate (AMR), Echo cancellation, Noise reduction
Adaptive Multi-rate (AMR), Echo cancellation, Noise reduction
- SIM card interface
4.2.2.
Power Supply Circuit
The power is supplied to the GSM module, Audio circuit, LCD, SIM card from Battery(+3.8v)as shown in Fig.101.The power
supply is as follows.
BAT+(3.8V)
supply is as follows.
BAT+(3.8V)
→ MOD1 → Audio circuit
BAT+(3.8V)
→ MOD1 → LCD
BAT+(3.8V)
→ MOD1 → SIM card
BAT+(3.8V)
→ LED Power IC → LED
BAT+(3.8V)
→ LDO → Vibrator
Fig.101
3.8V
VANA 2.5V
BAT+
GSM
Audio circuit
module
BAT-
MOD1
VIO 2.85V
LCD
VSIM 2.85/1.80V
SIM card
LED Power IC
IC3
IC3
LED
LDO
IC4
IC4
Vibrator
BAT
On
Off
VIO
2.85 V
2.85 V
Reset
(RETn)
(RETn)
1
2
3
S
Click on the first or last page to see other KX-TU301RUME service manuals if exist.