Panasonic UE-407019NA Service Manual / Supplement ▷ View online
Chapter 9
Options and Supplies
This chapter covers only the differences from the UF-885/895 Service Manual.
Panasonic G3 Communication Port Kit
50
9 Options
9.1
Installing G3 Communication Port Kit (UE-407019)
These instructions supersede the instructions provided on page 273 of the UF-885/895 Service Manual.
1. Contents
2. Installation
Note:
Before proceeding with the installation, prepare the Master Firmware Card with the appropriate Optional Firmware (V1.0000
or later). See page 48 of the Service Manual on how to create a Master Firmware Card.
Before proceeding with the installation, prepare the Master Firmware Card with the appropriate Optional Firmware (V1.0000
or later). See page 48 of the Service Manual on how to create a Master Firmware Card.
No.
Part No.
Description
Qty
Remarks
1.
DZEC101274
G3 PC Board
1
-
2.
DZYNA1435J
LCU PC Board
1
-
3.
DZFP000710
Harness, G3B-LCU
1
-
4.
DZFP000709
Ribbon Cable
1
-
5.
XYN3+F8
Screw
2
Screw with washer
6.
DZPB000007
Screw
2
Silver Colored Screw
7.
DZSD000882
Supplement User’s Guide
1
-
8.
DZSM000172
Installation Guide
1
This document
(1) Turn the
Power Switch to the OFF (O) position.
(2) Disconnect the Power Cord.
(3) Disconnect the Telephone Line Cable.
(4) Open the Control Panel.
(3) Disconnect the Telephone Line Cable.
(4) Open the Control Panel.
(5) Remove 1 Screw.
(6) Remove the Memory Card Cover.
(7) Remove 4 Screws.
(8) Remove the Sub Rear Cover.
(9) Remove the protective tabs on the Sub Rear Cover.
(6) Remove the Memory Card Cover.
(7) Remove 4 Screws.
(8) Remove the Sub Rear Cover.
(9) Remove the protective tabs on the Sub Rear Cover.
(10) Remove 1 Screw.
(11) Remove the Rear Access Cover.
(12) Remove 3 Screws.
(13) Remove the Rear Cover.
(14) Remove the protective tab.
(15) Reinstall the Rear Cover.
(13) Remove the Rear Cover.
(14) Remove the protective tab.
(15) Reinstall the Rear Cover.
Options
51
(16) Store the Rear Access Cover for future use by placing it
over the LCU PC Board and secure it with a silver colored
screw as illustrated on the left.
screw as illustrated on the left.
(17) Connect one end of the Ribbon Cable to the G3B PC
Board and the other end with a ferrite core to CN50 on the
FCB PC Board in the machine.
FCB PC Board in the machine.
(18) Align the 2 Hooks at the bottom of the G3 Communication
Port Assembly over the metal frame of the machine, and
then secure the assembly with the 4 screws that came with
the kit.
then secure the assembly with the 4 screws that came with
the kit.
Two screws with washer for the top and 2 silver colored
screws for the bottom.
screws for the bottom.
(19) Reinstall the Sub Rear Cover.
(20) Reconnect the Power Cord and the Telephone Line
(20) Reconnect the Power Cord and the Telephone Line
Cable.
(21) Insert the Master Firmware Card that you have prepared
into the Flash Memory Card slot in the machine.
(22) Turn the Power Switch to the ON (I) position.
(23) Perform the Service Mode 9-1 (Firmware Update). See
(23) Perform the Service Mode 9-1 (Firmware Update). See
page 186 of the Service Manual.
(24) Perform the Service Mode 6 (Parameter Initialization).
(25) Turn the Power Switch to the OFF (O) position.
(26) Remove the Master Firmware Card.
(27) Reinstall the Memory Card Cover.
(28) Turn the Power Switch to the ON (I) position.
(25) Turn the Power Switch to the OFF (O) position.
(26) Remove the Master Firmware Card.
(27) Reinstall the Memory Card Cover.
(28) Turn the Power Switch to the ON (I) position.
Printed in the U.S.A.
DZZSM080
DZZSM080