Panasonic KX-MB2051RUB / KX-MB2061RUB Service Manual ▷ View online
125
KX-MB2051RUB / KX-MB2061RUB
11.1.3. Service Function Table
Code
Function
Set Value
Effective
Range
Default
Remarks
501
Pause time set
1: 3s (Short)
2: 5s (Long)
2: 5s (Long)
1, 2
1
----------
507
V34 transmission start speed
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0~8
1
If the code 527 is set at 2, the code 507 and 508
work.
work.
508
V34 reception start speed
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0~8
1
If the code 527 is set at 2, the code 507 and 508
work.
work.
511
VOX sense
1:High 2:Low 1, 2
1
When the TAM (or EXT TAM) does not stop record-
ing the ICM because noise is detected on the tele-
phone line, change this setting to "LOW".
ing the ICM because noise is detected on the tele-
phone line, change this setting to "LOW".
514
Bell signal detect time
X 100msec
1~9
6
----------
520
CED frequency select
1:2100 Hz
2:1100 Hz
2:1100 Hz
1, 2
1
See How To Output The Journal Report (P.187).
521
International mode select
1:ON 2:OFF 1, 2
1
See How To Output The Journal Report (P.187).
522
Auto standby select
1:ON 2:OFF 1, 2
1
The resolution reverts to the default when transmis-
sion is complete.
sion is complete.
523
Receive equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
Set RX equalizer to automatic mode.
524
Transmission equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
527
V.8 function select
1:OFF 2:ON 1, 2
2
529
Call Service Clear
550
Memory clear
Refer to Memory Clear Specification (P.127).
551
ROM check
See Test Functions (P.121).
553
Monitor on FAX communication
select
select
1:OFF
2:PHASE B
3:ALL
2:PHASE B
3:ALL
1~3
1
Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
unit's speaker during FAX communication or not.
554
Modem test
See Test Functions (P.121).
555
Scanner test
See Test Functions (P.121).
556
Motor test
0
See Test Functions (P.121).
557
LED test
See Test Functions (P.121).
558
LCD test
See Test Functions (P.121).
561
KEY test
See Test Functions (P.121).
567
T0 timer
X second
001~255
031
Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
other party needs more time during automatic FAX
transmission.
570
BREAK % select
1:61%
2:67%
3:63%
2:67%
3:63%
1~3
1
Sets the % break of pulse dialing according PBX.
571
ITS auto redial time set
X number of
times
times
00~99
03
Selects the number of times that ITS is redialed
(not including the first dial).
(not including the first dial).
572
ITS auto redial line disconnection
time set
time set
X second
001~999
065
Sets the interval of ITS redialing.
574
Dial tone detect check
1: ON 2: OFF 1, 2
2
----------
590
FAX auto redial time set
X number of
times
times
00~99
03
Selects the number of redial times during FAX com-
munication (not including the first dial).
munication (not including the first dial).
591
FAX auto redial time disconnection
time set
time set
X second
001~999
065
Sets the FAX redial interval during FAX communi-
cation.
cation.
126
KX-MB2051RUB / KX-MB2061RUB
592
CNG transmit select
1:OFF
2:ALL
3:AUTO
2:ALL
3:AUTO
1~3
2
Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to Sometime There Is a Transmit Problem
(P.180).
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to Sometime There Is a Transmit Problem
(P.180).
593
Time between CED and 300bps
1:75 msec
2:500 msec
3:1 sec
2:500 msec
3:1 sec
1~3
1
See How To Output The Journal Report (P.187)
and Receive Problem (P.181).
and Receive Problem (P.181).
594
Overseas DIS detection select
1:detects
at
the 1st time
2:detects at
the 2nd time
2:detects at
the 2nd time
1, 2
1
See How To Output The Journal Report (P.187)
and Sometime There Is a Transmit Problem
(P.180).
and Sometime There Is a Transmit Problem
(P.180).
595
Receive error limit value set
1: 5%
2: 10%
3: 15%
4: 20%
2: 10%
3: 15%
4: 20%
1~4
2
If the number of errors during transmission exceeds
this value, the sending side terminates the call.
this value, the sending side terminates the call.
596
Transmit level set
X dBm
- 15~00
10
Selects the FAX transmission level. Refer to Some-
time There Is a Transmit Problem (P.180) and
Receive Problem (P.181).
time There Is a Transmit Problem (P.180) and
Receive Problem (P.181).
598
Receiving sensitivity
43= -43 dBm
20~48
48
Used when there is an error problem. Refer to How
To Output The Journal Report (P.187).
To Output The Journal Report (P.187).
599
ECM frame size
1:256 2:64
1, 2
1
----------
628
H.V.P.S. check
See Test Functions (P.121).
639
LSU test
See Test Functions (P.121).
655
Cause Distinction Code of Call Service 3
See CALL SERVICE Troubleshooting Guide
(P.153).
(P.153).
677
FAN test
See Test Functions (P.121).
710
Memory clear except History data
Refer to Memory Clear Specification (P.127).
717
Transmit speed select
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6
1
If the code 527 is set at 1, the code 717 and 718
work.
work.
718
Receive speed select
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6
1
If the code 527 is set at 1, the code 717 and 718
work.
work.
722
Redial tone detect
1:ON 2:OFF 1, 2
1
Sets the tone detection mode after redialing.
731
CPC mode
X 10 msec
000~255
033
Sets the CPC signal detection mode from the con-
verter.
verter.
732
AUTO disconnect cancel time
1:1 sec
2:3 sec
3:OFF
2:3 sec
3:OFF
1~3
1
When the auto disconnect circuit operates and cuts
the line.
the line.
763
CNG detect time for friendly reception 1:10 sec
2:20 sec
3:30 sec
3:30 sec
1~3
3
Selects the CNG detection tone of friendly recep-
tion.
tion.
774
Receiving T4 timer
X 100 msec
00~99
00
Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
communication.
(ex. Mobile comm) does not work well.
775
Transmission T4 timer
X 100m sec
00~99
00
Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
communication.
(ex. Mobile comm) does not work well.
784
Voice prompt test
You can hear the voice prompt from speaker after
pressing “SET” key.
pressing “SET” key.
815
Sensor check
See Test Functions (P.121).
852
Print test pattern
See Test Functions (P.121).
853
Top margin
X 0.5mm
01~11
06
----------
854
Left margin
X 0.5mm
01~11
06
----------
874
DTMF ON time
X msec
060~200
100
----------
875
DTMF OFF time
X 10 msec
06~20
10
----------
880
History list
See History (Example of a printed out list)
(P.136).
(P.136).
881
Journal 2 list
See Journal 2 (P.184).
882
Journal 3 list
See Journal 3 (P.185).
956
CORDLESS TEST MODE
Command
Code
Function
Set Value
Effective
Range
Default
Remarks
127
KX-MB2051RUB / KX-MB2061RUB
11.1.4. Memory Clear Specification
*
1
Execute Service Mode #550 when you want to reset the all setting data keeping the user information.
*
2
Execute Service Mode #710 to clear the user information in case that Main Unit is recycled.
Note:
Please restart a power supply after clearing a memory.
961
The time transmitting the false ring
back tone
back tone
X sec
01~10
05
Set the time transmitting the false ring back tone to
the line in TEL/FAX mode.
the line in TEL/FAX mode.
962
The operator calling time
X sec
05~30
13
Set the operator calling time through the speaker in
TEL/Fax mode.
TEL/Fax mode.
Code
Function
Set Value
Effective
Range
Default
Remarks
128
KX-MB2051RUB / KX-MB2061RUB
11.2. Cordless Handset
