DOWNLOAD Panasonic KX-FT932RU-B / KX-FT932CA-B / KX-FT932UA-B / KX-FT934RU-B / KX-FT934CA-B / KX-FT934UA-B Service Manual ↓ Size: 4.44 MB | Pages: 127 in PDF or view online for FREE

Model
KX-FT932RU-B KX-FT932CA-B KX-FT932UA-B KX-FT934RU-B KX-FT934CA-B KX-FT934UA-B
Pages
127
Size
4.44 MB
Type
PDF
Document
Service Manual
Brand
Device
Fax / PERSONAL FACSIMILE
File
kx-ft932ru-b-kx-ft932ca-b-kx-ft932ua-b-kx-ft934ru-.pdf
Date

Panasonic KX-FT932RU-B / KX-FT932CA-B / KX-FT932UA-B / KX-FT934RU-B / KX-FT934CA-B / KX-FT934UA-B Service Manual ▷ View online

57
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
11.1.3.
Service Function Table
Code
Function
Set Value
Effective 
Range
Default
Remarks
501
Pause time
X 100 msec
001~600
60
 ---------- 
502
Flash time
X 10 ms
01~99
85
 ---------- 
503
Dial speed select
1: 10 pps
2: 20 pps
1, 2
1
 ---------- 
514
Bell detection time
X 100 msec
1~9
6
 ---------- 
520
CED frequency select
1:2100 
Hz
2:1100 Hz
1, 2
1
See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive  
(P.83).
521
International mode select
1:ON   2:OFF
1, 2
1
See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive  
(P.83).
522
Auto standby select
1:ON   2:OFF
1, 2
1
The resolution reverts to the default when transmission
is complete.
523
Receive equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
524
Transmission equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
544
Document feed position adjustment
value set
1: 3 mm
2: 4 mm
3: 5 mm
4: 6 mm
5: 7 mm
1~5
3
If it is difficult to feed documents, raise the set value. If
multi documents feed occurs, lower the set value.
550
Memory Clear
See Memory Clear Specification (P.59).
551
ROM check
See Test Mode(P.54).
552
DTMF single tone test
1:ON   2:OFF
1, 2
2
For  the DTMF single test, single tone (single tone fre-
quency in the high and low group) are out from the
modem. ON will be DTMF and OFF will be single tone
.After the test, do not forget to return to the ON setting.
553
Monitor on FAX communication select
1:OFF
2:PHASE B
3:ALL
1~3
1
Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
554
Modem test
See Test Mode(P.54).
555
Scan check
See Test Mode(P.54).
556
Motor test
0
See Test Mode(P.54).
557
LED test
See Test Mode(P.54).
558
LCD test
See Test Mode(P.54).
559
Document jam detection select
1:ON   2:OFF
1, 2
1
Select the jam detection of a document during FAX
transmission/copying.
560
Cutter selection (KX-FT934 only)
1:ON   2:OFF
1, 2
1
Turns off the cutter function. 
561
KEY test
See Test Mode(P.54).
562
Cutter test (KX-FT934 only)
Press “SET” key.
570
BREAK % select
1:61%   2:67% 1, 2
1
Sets the % break of pulse dialing according PBX.
571
ITS auto redial time set
X  number  of
times
00~99
03
Selects the number of times that ITS is redialed (not
including the first dial).
572
ITS auto redial line disconnection time
set
X second
001~999
065
Sets the interval of ITS redialing.
573
Remote turn-on ring number set
X  number  of
rings
01~99
10
Sets the number of rings before the unit starts to
receive a document in the TEL mode.
574
DIAL TONE detection ON/OFF selec-
tion
1:ON   2:OFF
1, 2
2
Sets  the  whether to dial the Automatic dial number
before detecting dial tone or after detecting dialtone.
590
FAX auto redial time set
X  number  of
times
00~99
03
Selects the number of redial times during FAX commu-
nication (not including the first dial).
591
FAX auto redial time disconnection time
set
X second
001~999
065
Sets the FAX redial interval during FAX communication.
592
CNG transmit select
1:OFF
2:ALL
3:AUTO
1~3
2
Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem
 (P.81).
58
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
593
Time between CED and 300bps
1:75 msec
2:500 msec
3:1 sec
1~3
1
See  Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive
  (P.83). Refer to Receive
Problem(P.82) and The unit can copy, but cannot
transmit/receive  
(P.83).
594
Overseas DIS detection select
1:detects 
at
the 1st time
2:detects at
the 2nd time
1, 2
1
See  Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive 
  (P.83). Refer to Sometime
there is a transmit problem
(P.81) and The unit can
copy, but cannot transmit/receive  
(P.83)
.
595
Receive error limit value set
1: 5 %
2: 10 %
3: 15 %
4: 20 %
1~4
2
Sets the number of acceptable error lines when the
FAX reconstructs the received data. Refer to Receive
Problem
 (P.82).
596
Transmit level set
10 = -10 dBm
 00~15
11
Selects the FAX transmission level. Refer to Sometime
there is a transmit problem
 (P.81) and Receive Prob-
lem
 (P.82).
598
Receiving sensitivity
43 = -43 dBm
20~48
43
Used when there is an error problem. Refer to The unit
can copy, but cannot either transmit/receive long
distance or international communications 
(P.84)
.
710
Memory clear except History data
Refer to Memory Clear Specification (P.59).
717
Transmit speed selection
1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4
1
Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.81)
and  The unit can copy, but the transmission
and reception image are incorrect
 (P.86).
718
Receive speed selection
1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4
1
Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.82) and The unit
can copy, but the transmission and reception image
are incorrect 
(P.86).
722
Redial tone detect
1:ON   2:OFF
1, 2
1
Sets the tone detection mode after redialing.
732
AUTO disconnect cancel time
X 100 ms
1~3
1
When the auto disconnect circuit operates and cuts the
line.
745
Power ON film feed
1:ON   2:OFF
1, 2
1
Invalid function for thermal model.
763
CNG detect time for friendly reception
1:10 sec
2:20 sec
3:30 sec
1~3
3
Selects the CNG detection tone of friendly reception.
774
T4 timer
X 100 msec
00~99
00
Use  this  function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
815
Sensor check
See Test Mode(P.54).
852
Print test pattern
See Test Mode(P.54).
853
Top margin
1~9
 3
 ---------- 
874
DTMF ON time
X msec
60~20
10
 ---------- 
875
DTMF OFF time
X msec
60~20
10
 ---------- 
880
History list
 ---------- 
881
Journal 2 list
See Special service journal reports (P.76).
882
Journal 3 list
See Special service journal reports (P.76).
961
The time transmitting the false ring back
tone
X sec
01~10
05
Set the time transmitting the false ring back tone to the
line in TEL/FAX mode.
962
The operator calling time
X sec
05~30
13
Set  the operator calling time through the speaker in
TEL/Fax mode.
Code
Function
Set Value
Effective 
Range
Default
Remarks
59
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
11.1.4.
Memory Clear Specification
*
1
 Execute Service Mode #550 when you want to reset the all setting data keeping the user information.
*
2
 Execute Service Mode #710 to clear the user information in case that Main Unit is recycled.
Note:
Please restart a power supply after clearing a memory.
60
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
11.2. The Example of the Printed List
11.2.1.
User Mode (Example of a printed out list)
(FT932/KX-FT934)
Note:
The above values are the default values.
Page of 127
Display

Click on the first or last page to see other KX-FT932RU-B / KX-FT932CA-B / KX-FT932UA-B / KX-FT934RU-B / KX-FT934CA-B / KX-FT934UA-B service manuals if exist.