Panasonic KX-FT57E Service Manual ▷ View online
|
13
|
INTRODUCTION
KX-FT57E
CONNECTION
Note:
This machine should be connected to a nearby power outlet that is easily accessible.
DIALING MODE
PULSE
TONE
Dialing mode switch:
Set to TONE.
Set to TONE.
If you cannot dial,
set to PULSE.
To a single telephone line socket
Telephone line cord
Power cord
To the power outlet
(220-240V)
(220-240V)
|
14
|
KX-FT57E
Hooks
Dotted mark
INSTALLATION
1
2
4
5
6
Handset cord
Handset
Tab
Black lid
Front lid
Front lid open
button
button
Triangles
1. Installing the handset cradle
Connect the handset cord.
Open the front lid by pressing the front lid open
button.
button.
Open the back lid by lifting up the tabs located
on the both side.
on the both side.
Insert the handset cradle by matching the triangles.
Place the handset on the handset cradle and close
the lids securely.
the lids securely.
•
If the handset cradle is not installed correctly, the
unit will show the following message when the
power is switched on.
power is switched on.
CHECK CRADLE
Check steps 4 and 5 again.
Press down on the dotted mark on the handset
cradle until it clicks into place.
cradle until it clicks into place.
•
Make sure the two hooks lock the handset
cradle firmly.
3
Note:
•
To save space or when using the unit mainly for faxes, you can use the DIGITAL SP-PHONE button on the
unit without the handset and cradle.
|
15
|
INTRODUCTION
KX-FT57E
2. Installing the recording paper
1
Open the back lid by lifting up the tabs located
on the both sides.
on the both sides.
Install a recording paper roll.
•
Make sure that the shiny side of the paper is
facing down.
Note:
•
Only use the included roll of paper or specified recording paper, or the print quality may be affected and/or
excessive thermal head wear may occur.
4
Close the back lid by gently pressing down on both
ends.
ends.
Insert the leading edge of the recording paper
between the recording paper roller and the silver
plate, then pull it a few centimeters out of the unit.
between the recording paper roller and the silver
plate, then pull it a few centimeters out of the unit.
•
Make sure that there is no slack in the paper roll.
incorrect
correct
Tab
Recording paper roller
Silver plate
3. Installing the paper stacker
Install the paper stacker.
Paper stacker
3
2
•
If the paper is secured with glue or tape, cut
approx. 150 mm from the beginning of the roll.
|
16
|
KX-FT57E
To correct a mistake
• Use or to move the cursor to the incorrect
character, then make the corrections.
character, then make the corrections.
To delete a character
• Move the cursor to the character you want to delete and
press STOP .
4. SETTING YOUR LOGO
The logo can be a company, division or name.
(1) Press MENU .
Display:
1. SYSTEM SET UP
(2) Press # , then 0 2 .
YOUR LOGO
(3) Press START/COPY/SET .
LOGO=
(4) Enter your logo, up to 30 characters, by following the
instructions on the next page.
Example (using the dial keypad): Bill
1. Press 2 twice.
LOGO=B
2. Press 4 six times.
LOGO=Bi
3. Press 5 six times.
LOGO=Bil
4. Press ( VOLUME ) to remove the cursor
and press 5 six times.
LOGO=Bill
• To enter the same number key continuously,
move the cursor to the next space.
move the cursor to the next space.
(5) Press START/COPY/SET .
SYSTEM SET UP [ ]
(6) Press MENU .
To insert a character
1. Press or to move the cursor to the
position to the right of where you want to
insert the character.
2. Press INSERT to insert a space and enter
the character.
Note:
• You can enter your logo by rotating
EASY DIAL (See next page).
• You can enter your logo by rotating
EASY DIAL (See next page).
INSERT
MENU
(Delete)
STOP
START/COPY/SET
EASY DIAL
/
Click on the first or last page to see other KX-FT57E service manuals if exist.