Panasonic KX-FT25LA Service Manual ▷ View online
2.4.7.1.
JOURNAL 3
Descriptions:
1. ENCODE
Compression Code: MH/MR
2. MSLT
MSLT means Minimum Scan Line Time. Used only at the factory.
3. RESOLUTION (RESOL)
Indicates the resolution of the communication. If multiple pages are transmitted or received, it indicates the last page´s
resolution. If there is a communication error, “?” is displayed.
resolution. If there is a communication error, “?” is displayed.
4. SPEED
Indicates the speed of communication. If multiple pages are transmitted or received, it indicates the last page´s communication
speed. If there is a communication error, “?” is displayed.
speed. If there is a communication error, “?” is displayed.
5. RCV-TRIG. (CNT.)
Indicates the trigger that causes the unit to switch to the fax receive mode. The available options are listed in JOURNAL 3 in
2.4.7.2. PRINTOUT EXAMPLE. The values in parentheses indicate how many times the trigger has been used. (For example,
“0003” means three times.)
2.4.7.2. PRINTOUT EXAMPLE. The values in parentheses indicate how many times the trigger has been used. (For example,
“0003” means three times.)
No.
Display
Function
1
FAX MODE
Means the unit received a fax message in the FAX mode.
2
MAN RCV
Means the unit received a fax message by manual operation.
3
FRN RCV
Means the unit received a fax message by friendly signal detection.
4
RMT DTMF
Means the unit detected DTMF (Remote Fax activation code) entered remotely.
5
PAL DTMF
Means the unit detected DTMF (Remote Fax activation code) entered by a parallel connected telephone.
6
TURN-ON
Means the unit started to receive after 15 rings. (Remote Turn On: Service Code #573)
7
TIME OUT
Means the unit started to receive after Ring Time Out in the EXT-TAM or TEL/FAX mode.
8
IDENT
Means the unit detected Ring Detection.
9
TEL/FAX
Means the unit detected the CNN while it was sending the Dummy Ring Back Tone in the TEL/FAX mode.
NO RESPONSE DISAPPEARED ON JOURNAL
The “NO RESPONSE DISAPPEARED ON JOURNAL” displays the information about the last 10 communications terminated
by “No Response”. (Some of the communications terminated by “No Response” were not displayed in the JOURNAL.)When a
fax transmission cannot be performed because the other party´s unit is set to the TEL mode, “No response” will be printed.
by “No Response”. (Some of the communications terminated by “No Response” were not displayed in the JOURNAL.)When a
fax transmission cannot be performed because the other party´s unit is set to the TEL mode, “No response” will be printed.
6. EQM
EQM means Eye Quality Monitor. Used only at the factory.
7. ERROR LINE(RX)
When an error occurs while receiving a fax, this shows the number of error lines.
8. MAKER CODE
This shows a 2 digit code of the other partyís fax machine brand.
0E: “KX” model
00: Unknown
79: “UF” model
19: “Xerox” model
00: Unknown
79: “UF” model
19: “Xerox” model
2.4.7.2. PRINTOUT EXAMPLE
85
KX-FT25LA
2.5.
TEST FUNCTIONS
86
KX-FT25LA
2.5.1. DTMF SIGNAL TONE TRANSMIT SELECTION
Note:
After performing this check, do not forget to turn the setting off.
Otherwise, dialing using DTMF will not be possible.
2.5.2. BUTTON CODE TABLE
Note:
These codes (00, 01) are only for the data in the History Report.
2.5.3. PRINT TEST PATTERN
87
KX-FT25LA
3 ADJUSTMENTS
3.1. ADJUSTING THE FEED PRESSURE
If no feeding or multiple feeding occurs frequently, adjust the feeder pressure.
1. Open the front lid by pressing the front lid open.
2. Shift the position of the lever using an instrument with a pointed end, such as paper clip.
Right: When documents do not feed.
Center: Standard position (pre-selected)
Left: When documents multiple feed.
3. Close the front lid by gently pressing down on both ends.
Note:
Touch the lever using an instrument with a pointed end such as ball-point pen because the lever is located in a small place.
88
KX-FT25LA
Click on the first or last page to see other KX-FT25LA service manuals if exist.