Panasonic KX-FLC418RU Service Manual ▷ View online
9
KX-FLC418RU
2.2.
Discarding of P. C. Board
When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.
2.3.
Insulation Resistance Test
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
(screw heads, control shafts, bottom frame, etc.).
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.
2.4.
Battery Caution
CAUTION
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
The lithium battery is a critical component (type No.BR2032). Please observe for the proper polarity and exact location when
replacing it and the soldering the replacement lithium battery in.
replacing it and the soldering the replacement lithium battery in.
2.5.
Note for Repairing
Caution
Please inform users of the danger of data being lost at the time of repair.
Data will be lost in the following situations.
1. When replacing the ROM ass'y.
2. When replacing the Main board ass'y.
3. When executing mode #550 or #710.
2. When replacing the Main board ass'y.
3. When executing mode #550 or #710.
There is a possibility of data loss in the following situations.
1. When removing a board.
2. When writing new software to ROM.
2. When writing new software to ROM.
10
KX-FLC418RU
3 Specifications
3.1.
Base Unit
*1 Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other
party's machine.
*2 Transmission speed is based upon the ITU-T No. 1 Test Chart. (Refer to ITU-T No.1 Test Chart (P.262).) If the capability of the
other party's machine is inferior to your unit, the transmission time may be longer.
*3 If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
*4 Recording time may be reduced by the calling party's background noise.
Note:
party's machine.
*2 Transmission speed is based upon the ITU-T No. 1 Test Chart. (Refer to ITU-T No.1 Test Chart (P.262).) If the capability of the
other party's machine is inferior to your unit, the transmission time may be longer.
*3 If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
*4 Recording time may be reduced by the calling party's background noise.
Note:
• Design and specifications are subject to change without notice.
• The pictures and illustrations in these instructions may vary slightly from the actual product.
Applicable Lines:
Public Switched Telephone Network
Document Size:
Max. 216 mm in width
Max. 600 mm in length
Max. 600 mm in length
Effective Scanning Width:
208 mm
Effective Printing Width:
202mm
Transmission Time
*1
:
Approx. 8 s/page (ECM-MMR)
*2
Scanning Density:
Horizontal:
8 pels/mm
Vertical:
3.85 lines/mm -STANDARD
7.7 lines/mm -FINE/PHOTO/MIXED(PHOTO WITH TEXT)
15.4 lines/mm -SUPER FINE
8 pels/mm
Vertical:
3.85 lines/mm -STANDARD
7.7 lines/mm -FINE/PHOTO/MIXED(PHOTO WITH TEXT)
15.4 lines/mm -SUPER FINE
Photo Resolution:
64-level
Scanner Type:
Contact Image Sensor (CIS)
Printer Type:
Laser printer
Data Compression System:
Modified Huffman (MH), Modified READ (MR), Modified Modified READ (MMR)
Modem Speed:
14,400/12,000/9,600/7,200/4,800/2,400 bps; Automatic Fallback
Operating Environment:
10
°C—32.5°C, 20—70% RH (Relative Humidity)
Dimensions:
Approx. height 218 mm
× width 360 mm × depth 357 mm
Mass (Weight):
Approx. 7.5 kg
Power Consumption:
Standby: Approx. 4.0 W
Transmission: Approx. 12W
Reception: Approx. 240 W
Copy: Approx. 240 W
Maximum: Approx. 950W (When the fuser lamp turns on)
Transmission: Approx. 12W
Reception: Approx. 240 W
Copy: Approx. 240 W
Maximum: Approx. 950W (When the fuser lamp turns on)
Power Supply:
220-240 V AC, 50/60Hz
FAX Memory Capacity
*3
:
Approx. 150 pages of memory transmission.
Approx. 40 pages of memory reception.
(Based on ITU-T No. 1 Test Chart in standard resolution.)
Approx. 40 pages of memory reception.
(Based on ITU-T No. 1 Test Chart in standard resolution.)
Voice memory capacity
*4
:
Approx. 15 minutes of recording time
Copy memory capacity:
Approx. 80 pages (Based on the ITU-T No. 1 Test Chart in fine resolution.)
Laser diode properties:
Laser output: Max. 5 mW
Wave length: 760 nm—800 nm
Emission duration: Continuous
Wave length: 760 nm—800 nm
Emission duration: Continuous
LED light of CIS properties:
LED radiation output: Max. 1 mW
Wavelength: Green 520 nm typ.
Emission duration: Continuous
Wavelength: Green 520 nm typ.
Emission duration: Continuous
Copy Speed:
Approx 10 cpm (copies per minute)
Printing Resolution:
600
× 600 dpi
Product life:
2 hundreds-thousands (except drum unit, toner cartridge)
11
KX-FLC418RU
3.2.
Cordless Handset
3.3.
Charger Unit
Standard:
DECT (Digital Enhanced Cordless Telecommunications)
GAP (Generic Access Profile)
GAP (Generic Access Profile)
Number of channels:
120 Duplex Channels
Frequency range:
1.88 GHz to 1.9 GHz
Duplex procedure:
TDMA (Time Division Multiple Access)
Channel spacing:
1,728 kHz
Bit rate:
1,152 kbit/s
Modulation:
GFSK (Gaussian Frequency Shift Keying)
RF transmission power:
Approx. 10 mW (average power per channel)
Voice coding:
ADPCM 32 kbit/s
Operating environment:
5
°C - 40 °C, 20 % - 80 % RH (Relative Humidity)
Operating Range:
Up to 300 m outdoors, Up to 50 m indoors, depending on the condition
Dimensions:
Approx. height 158 mm
× width 48 mm × depth 30 mm
Mass (Weight):
Approx. 130 g
Operating environment:
5
°C - 40 °C, 20 % - 80 % RH (Relative Humidity)
Dimensions:
Approx. height 52 mm
× width 75 mm × depth 88 mm
Mass (Weight):
Approx. 60 g
Power consumption:
Standby: Approx. 0.2 W
Maximum: Approx. 3.2 W
Maximum: Approx. 3.2 W
Power supply:
AC adaptor (220 V - 240 V AC, 50/60 Hz)
12
KX-FLC418RU
4 General/Introduction
4.1.
Optional Accessories
*
1
Replacement batteries may have a different capacity from that of the supplied batteries.
4.2.
Translation List
4.2.1.
Error Message (Display)
Model No.
Description
Specifications
KX-FAT88A/
KX-FAT88A7
KX-FAT88A7
Toner cartridge
1 toner cartridge
KX-FAD89A/
KX-FAD89A7
KX-FAD89A7
Drum unit
1 drum unit
P03P or HHR-4MRE
Rechargeable nickel metal hydride (Ni-MH)
battery*
battery*
1
2 batteries (AAA (R03) size)
KX-TGA641RU
additional digital cordless handset
-
KX-A272
DECT repeater
-
Click on the first or last page to see other KX-FLC418RU service manuals if exist.