Panasonic DMP-BDT210EB / DMP-BDT210EF / DMP-BDT210EG Service Manual ▷ View online
29
10 Disassembly and Assembly Instructions
10.1. Unit
10.1.1.
Disassembly Flow Chart
The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the ser-
vicing.
To assemble the unit, reverse the steps shown in the chart below.
vicing.
To assemble the unit, reverse the steps shown in the chart below.
10.1.2.
P.C.B. Positions
30
10.1.3.
Top Case
10.1.3.1. Tray Ornament
1. Remove the 3 screws (A).
2. Slide Top Case rearward and open the both ends at rear
2. Slide Top Case rearward and open the both ends at rear
side of the Top Case a little and lift the Top Case in the
direction of the arrows.
direction of the arrows.
3. Remove the wire with connector (A), then remove the Top
Case.
10.1.3.2. Barrier Top
1. Unlock 2 tabs then pull with the Barrier Top in the direc-
tion of your side.
10.1.3.3. Sensor P.C.B.
1. Pushing the 2 lockng tabs in dirrection of (1), pull the Sen-
sor P.C.B. in dirrection of (1) and remove the Sensor
P.C.B..
P.C.B..
10.1.4.
Front Panel
10.1.4.1. Tray Ornament
1. Remove the Drive Cover in direction of (1).
2. Perform the step “6. 1. Taking out the Disc from Drive Unit
2. Perform the step “6. 1. Taking out the Disc from Drive Unit
when the Disc cannot be ejected by OPEN/CLOSE but-
ton” and eject tray.
ton” and eject tray.
3. Unlock 2 tabs turn,
Pull the Tray Ornament in direction of (2).
31
10.1.4.2. Front Panel
1. Remove the wire with connector (A).
2. Unlock 6 tabs (A) - (F) turn.
2. Unlock 6 tabs (A) - (F) turn.
Pull with the Front Panel in the direction of your side.
10.1.4.3. LED P.C.B.
1. Unlock 2 tabs turn.
Remove the LED P.C.B..
10.1.4.4. How to assemble the Tray door
ass’y
1. Attach 4 tabs of Tray door ass’y to shafts of the Front
Panel though the holes.
2. Slide the Tray door ass’y and attach the Door Stopper to
the Tray door ass’y.
3. Attach the Door Spring to Tray door ass’y.
10.1.5.
Power SW P.C.B.
1. Remove the wire with connector (A).
2. Remove the screw (A) to remove Power SW P.C.B..
2. Remove the screw (A) to remove Power SW P.C.B..
32
10.1.6.
Rear Panel
1. Remove the 4 screws (A) and screw (B).
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
10.1.7.
SD USB P.C.B.
1. Remove the wire with connector (A).
2. Remove the screw (A) and screw (B) to remove SD USB
2. Remove the screw (A) and screw (B) to remove SD USB
P.C.B..
10.1.8.
Wireless LAN Module
1. Remove the wire with connector (A).
2. Remove the 2 screws (A) to remove the Wireless LAN
2. Remove the 2 screws (A) to remove the Wireless LAN
Module.
3. Remove the screw (B) to remove the WIFI Angle.
10.1.9.
BD Power P.C.B.
1. Remove the wire with connector (A) and connector (B).
2. Remove the 2 screws (A) to remove BD Power P.C.B..
2. Remove the 2 screws (A) to remove BD Power P.C.B..
Click on the first or last page to see other DMP-BDT210EB / DMP-BDT210EF / DMP-BDT210EG service manuals if exist.