Panasonic DMP-BDT100EE / DMP-BDT100EG Service Manual ▷ View online
29
10.1.3.
Top Case
1. Remove the 2 screws (A) and 3 screws (B).
2. Slide Top Case rearward and open the both ends at rear
2. Slide Top Case rearward and open the both ends at rear
side of the Top Case a little and lift the Top Case in the
direction of the arrows.
direction of the arrows.
10.1.4.
Front Panel
1. Unlock 6 tabs (A) - (F) turn.
Pull with the Front Panel in the direction of your side.
10.1.5.
Power SW P.C.B. and FL P.C.B.
10.1.5.1. Power SW P.C.B. and FL P.C.B.
1. Remove the screw (A).
2. Remove the Power SW P.C.B..
3. Remove the 3 screws (B).
4. Remove the FL P.C.B..
2. Remove the Power SW P.C.B..
3. Remove the 3 screws (B).
4. Remove the FL P.C.B..
10.1.5.2. How to assemble the Tray door
ass’y
1. Attach the Tray door spring to Tray door ass’y.
2. Attach Tray door ass’y in order from [1] to [2].
[1]: Insert the shaft to the hole.
[2]: Insert the shaft to the hole.
[2]: Insert the shaft to the hole.
30
3. Confirm the Tray door spring is attached as following.
10.1.6.
BD Drive Unit
1. Remove the wire with connector (A) and (B).
2. Remove the FFC.
3. Remove the 4 screws (A) to remove BD Drive Unit.
2. Remove the FFC.
3. Remove the 4 screws (A) to remove BD Drive Unit.
10.1.7.
Chassis Angle
1. Remove the 2 screws (A) and remove the Chassis Angle.
10.1.8.
Rear Panel
1. Remove the 4 screws (A) and 1 screw (B).
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
10.1.9.
Power P.C.B.
1. Remove the wire with connector (A).
2. Remove the 2 screws (A) to remove Power P.C.B..
2. Remove the 2 screws (A) to remove Power P.C.B..
10.1.10. Digital P.C.B.
1. Remove the wire with connector (A) , (B) and (C).
2. Remove the FFC.
3. Remove the 2 screws (A) to remove Digital P.C.B..
2. Remove the FFC.
3. Remove the 2 screws (A) to remove Digital P.C.B..
31
10.2. BD Drive
10.2.1.
Upper Base Ass’y
1. Remove the 4 Screws (A), and push the Hook in.
2. Lift up the Upper Base Ass’y, and pull it out to the direc-
tion of arrow.
10.2.2.
Tray
1. Perform the step “10. 2. 1. Upper Base Ass’y”.
2. Insert the paper clips, etc. into the hole of the bottom side,
2. Insert the paper clips, etc. into the hole of the bottom side,
and slide it to the direction of arrow until it can be.
3. Pull the Tray to the direction of arrow until it can be.
4. Insert the paper clips, etc. into the hole of the Tray at 45
degrees, and lean it to the direction of arrow with pushing
the dotted point of the tray forward.
the dotted point of the tray forward.
32
5. Insert the paper clips, etc. into the Tray as below figure,
lift up the lever using the Eject Pin while pushing the dot-
ted point of the Tray.
ted point of the Tray.
10.2.3.
Pulley Gear, Belt
1. Perform the step “10. 2. 2. Tray”.
2. Push the Post to the direction of arrow by using the slot-
2. Push the Post to the direction of arrow by using the slot-
ted screwdriver.
3. Remove the Pulley Gear and Belt.
10.2.4.
Slide Cam
1. Perform the step “10. 2. 3. Pulley Gear, Belt”.
2. Disconnect the 3 FFCs.
3. Remove the 2 Screws (B) to remove the Radiator Plate.
4. Open the connector lock, and disconnect the FFC (A).
5. Remove the Drive P.C.B..
2. Disconnect the 3 FFCs.
3. Remove the 2 Screws (B) to remove the Radiator Plate.
4. Open the connector lock, and disconnect the FFC (A).
5. Remove the Drive P.C.B..
Caution:
Though the Drive P.C.B. is not supplied as replace-
ment parts, it must be removed for after disassem-
bling.
ment parts, it must be removed for after disassem-
bling.
6. Open the connector lock, and disconnect the FFC.
7. Remove the 2 Screws (C), and remove the Traverse
7. Remove the 2 Screws (C), and remove the Traverse
Base Ass'y with spreading the 2 hooks to the direction of
arrows.
arrows.
Click on the first or last page to see other DMP-BDT100EE / DMP-BDT100EG service manuals if exist.