Panasonic H-H014PP / H-H014E / H-H014GK Service Manual ▷ View online
9
4 Disassembly/Assembly procedures
4.1.
Disassembly/Assembly procedures
It is recommended dealing with Clean box, to keep maintaining the dustproof environment.
(Refer to “3.2. Clean Box” section of this service manual for details.)
IMPORTANT:
(Refer to “3.2. Clean Box” section of this service manual for details.)
IMPORTANT:
1. When servicing the surrounding part with red line (refer to Fig.D1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 Federal Standard 209D).
As for procedure, refer to the "5 Maintenance" for details.
As for procedure, refer to the "5 Maintenance" for details.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with Lens caps
(front & rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/ and assemble, by referring the following table and Fig.D1.
NOTE:
1. When tightening the screw, use a Torque driver (RFKZ0456) by ordering the screwing order with specified torque
mentioned in each step.
2. The screw Ref.B209 is no need to remove for disassembly.
3. Use VFK1390 (small driver) when screwing/unscrewing the B209 and B210.
3. Use VFK1390 (small driver) when screwing/unscrewing the B209 and B210.
Fig. D1
10
5 MAINTENANCE
5.1.
ABOUT THE LENS
5.1.1.
DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
5.1.2.
DUST/DIRT ON THE LENS GLASSES
Define the location of the dust/dirt first, whether it is outside
lens surface or not.
lens surface or not.
1. When it is outside surface of the lens:
When the dust and/or dirt gets on the outer side surface
of the Lens glasses, order the following procedures.
of the Lens glasses, order the following procedures.
a. Blow off the dust on the Lens glass surface with the
Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with Lens
cleaning KIT (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)
2. When it is inside of the lens:
Refer to the “5.3 Method of cleaning inside of lens”
section of this service manual.
section of this service manual.
5.2.
General description (Lens cleaning)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit,
remove it by referring the following procedures.
remove it by referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 Federal Standard 209D)
As for clean box, refer to the “3.2. CLEAN BOX”, in details.
As for clean box, refer to the “3.2. CLEAN BOX”, in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
11
5.3.
Method of cleaning inside of lens
5.3.1.
Disassembly Procedure
IMPORTANT
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 Federal
Standard 209D).
(Satisfied clean level: Less than class 10,000 Federal
Standard 209D).
1. Removal of the Decoration Ring
*.Decoration ring is sticked on the 1st lens frame unit.
*.Put the sheet so that the lens glass is fully covered.
*.Insert the needle to Gap “A” (between the Decoration
ring and Lens glass), and peel off the Decoration ring
gentlly.
*.Put the sheet so that the lens glass is fully covered.
*.Insert the needle to Gap “A” (between the Decoration
ring and Lens glass), and peel off the Decoration ring
gentlly.
2. Removal of the 1st Lens frame unit
*.Remove 3 screws (A).
*. Blow off the dust on the surface of the lens with a blower
brush.
*. Use lens cleaning KIT (BK)(VFK1900BK), if necessary.
5.3.2.
Assembly Procedure
IMPORTANT NOTICE:
*.When tightening the screw, use a Torque driver
(RFKZ0456) by ordering the screwing order with specified
torque descrived in each step.
(RFKZ0456) by ordering the screwing order with specified
torque descrived in each step.
1. Installation of the 1st Lens frame unit
*Tighten the 3 screws (A) with specified torgue in
numerical order.
numerical order.
2. Installation of the Decoration ring
*Install the Decoration ring by referring the phase mark.
(Use new one, Do not use the one which is removed.)
(Use new one, Do not use the one which is removed.)
* After installing the Decoration ring, press the decoration ring
with your finger.
12
6 EXPLODED VIEWS
6.1.
Frame & Casing Section
Click on the first or last page to see other H-H014PP / H-H014E / H-H014GK service manuals if exist.