Panasonic DMC-LZ7P / DMC-LZ7PC / DMC-LZ7PL / DMC-LZ7EB / DMC-LZ7EE / DMC-LZ7EF / DMC-LZ7EG / DMC-LZ7EGM / DMC-LZ7GC / DMC-LZ7GK / DMC-LZ7GN / DMC-LZ7EE9 Service Manual ▷ View online
25
4. Remove the 3 cam caps.
5. Pull down the plate part of master frange unit (refer to
arrow(1)), and then turn the master flange unit to counter-
clockwise fully (refer to arrow(2)).
clockwise fully (refer to arrow(2)).
6. Remove the direct frame/drive frame/1st lens frame/2nd
lens frame unit to the indicated by arrow.
8.4.2.
Removal of the Direct Frame Unit
1. Turn the drive frame unit to the indicated by arrow.
(Retracting direction)
2. Remove the direct frame/1st lens frame/2nd lens frame
unit from drive frame to the indicated by arrow.
3. Push the 1st lens frame/2nd lens frame unit from lens
front side, and then remove the 1st lens frame/2nd lens
frame unit from direct frame.
frame unit from direct frame.
26
8.5.
Assembly Procedure for the
Lens
Lens
8.5.1.
Phase alignment of the Direct
Frame and Drive Frame Unit
Frame and Drive Frame Unit
8.5.2.
Phase alignment of the Direct/Drive
Frame Unit and 1st Lens Frame/2nd
Lens Frame Unit
Frame Unit and 1st Lens Frame/2nd
Lens Frame Unit
8.5.3.
Phase alignment of the
1st Lens Frame/2nd Lens Frame/
Drive Frame/ Direct Frame Unit
and Master Flange Unit
1st Lens Frame/2nd Lens Frame/
Drive Frame/ Direct Frame Unit
and Master Flange Unit
27
8.5.4.
Assembly for the Zoom Motor Unit
8.5.5.
Assembly for the Cam Cap
8.6.
Removal of the CCD Unit
To prevent the CCD unit from catching the dust and dirt, do not
remove the CCD unit except for replacing.
remove the CCD unit except for replacing.
• Torx driver (T3) Part No. RFKZ0334
28
9 Measurements and Adjustments
9.1.
Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-PAVC”.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-PAVC”.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
NOTE:
*There is no LCD adjustment in this model.
*There is no CCD Black scratch compensation adjustment (BKI) in this model.
*There is no CCD Black scratch compensation adjustment (BKI) in this model.
Replaced Part
Adjustment Item
Main P.C.B.
VENUS
(IC6001)
Flash-ROM
(IC6002)
Lens Part
(Excluding
CCD)
CCD Unit
Camera
Section
Section
OIS hall element adjustment
(OIS)
(OIS)
O
O
O
O
Back focus adjustment
(BF)
(BF)
O
O
O
O
Shutter adjustment
(SHT)
(SHT)
O
O
O
O
O
ISO sensitivity adjustment
(ISO)
(ISO)
O
O
O
O
O
AWB adjustment
High brightness coloration inspection
(WBL)
High brightness coloration inspection
(WBL)
O
O
O
O
O
CCD white scratch compensation
(WKI)
(WKI)
O
O
O
O
Click on the first or last page to see other DMC-LZ7P / DMC-LZ7PC / DMC-LZ7PL / DMC-LZ7EB / DMC-LZ7EE / DMC-LZ7EF / DMC-LZ7EG / DMC-LZ7EGM / DMC-LZ7GC / DMC-LZ7GK / DMC-LZ7GN / DMC-LZ7EE9 service manuals if exist.