Panasonic DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG Service Manual ▷ View online
6.3. HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP C.B.A.
CAUTION:
1. Be sure to discharge the capacitor on FLASH TOP C.B.A..
2. Be careful of the high voltage circuit on FLASH TOP C.B.A. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k
Ω
/5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on FLASH TOP C.B.A. for approx. 5 seconds.
4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.
6.4. CLEANING LENS AND LCD PANEL
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
A lens cleaning paper and lens cleaner are available at local camera shops and market place.
13
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
7 ADJUSTMENT PROCEDURES
Even if the MAIN C.B.A. is replaced as a unit, it must be achieved the adjustment and factory setting. The adjustment in
this unit is separated two types as shown below.
this unit is separated two types as shown below.
The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System".
1. Main unit adjustment: All adjustments except for LCD adjustment.
This unit mounts the adjustment software for main unit, it wouldn’t need the connection between the PC and this unit with USB
cable.
cable.
2. LCD adjustment: Adjustment for LCD.
It need the connection between the PC and this unit with USB cable.
The adjustment instruction is available at "Software download" on the CS-Web from AVC" web-site in "TSN System", together
with maintenance software.
with maintenance software.
14
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
7.1. SERVICE FIXTURE AND TOOLS
The following Service Fixture and tools are used for checking and servicing this unit.
15
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
8 ERROR CODE MEMORY FUNCTION
1. General description
This unit is equipped with history of error code memory function, and can be memorized 32 error codes in sequence from the
latest. When the error is occurred more than 32, oldest error is overwritten in sequence.
latest. When the error is occurred more than 32, oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the
battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
2. How to display
The error code can be displayed by the following procedure:
Before perform the error code memory function, connect the AC adaptor or insert the battery.
Since this unit has built-in memory, this error code memory function can be performed without inserting SD card.
·
1. The temporary cancellation of factory setting:
Set the mode dial to “ Normal Picture
(Red camera mark)”.
While keep pressing Optical Image Stabilizer
and “ UP
of Cross key” simultaneously and hold them, turn the Power on.
·
2. The display of error code:
Press Optical Image Stabilizer , MENU
and “ LEFT
of Cross key” simultaneously with the step 1 condition.
The display is changed as shown below when the above buttons is pressed simultaneously.
Normal display
→
Error code display
→
Operation history display
→
Normal display
→
.....
Example of Error Code Display
·
3. The change of display:
The error code can be memorized 32 error codes in sequence, however it is displayed 5 errors on the LCD.
Display can be changed by the following procedure:
" UP
or DOWN
of Cross key": It can be scroll up or down one.
" LEFT
or RIGHT
of Cross key": It can be display last 5 error or another 5 error.
·
4. How to read the error code:
One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below.
16
DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG
Click on the first or last page to see other DMC-LS1PP / DMC-LS1PL / DMC-LS1EB / DMC-LS1EG / DMC-LS1EGM / DMC-LS1GC / DMC-LS1GK / DMC-LS1GN / DMC-LS1GT / DMC-LS1SG service manuals if exist.