Panasonic DMC-GF1CPP / DMC-GF1CEB / DMC-GF1CEC / DMC-GF1CEG / DMC-GF1CGC / DMC-GF1CGH / DMC-GF1CGK / DMC-GF1CGN / DMC-GF1KPP / DMC-GF1KEB / DMC-GF1KEC / DMC-GF1KEG / DMC-GF1KGC / DMC-GF1KGH / DMC-GF1KGK / DMC-GF1KGN / DMC-GF1PP / DMC-GF1EB / DMC-GF1EC / DMC-GF1EG / Service Manual ▷ View online
61
10 Measurements and Adjustments
10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
*1
• Inspect it, not only corresponding part is replaced, but also camera body is shocked and/or dropped.
• The DMC-G1/DMC-GH1/DMC-GF1 unit (marketed commodity: operates normal) etc. in accordance with the Micro Four Thirds
• The DMC-G1/DMC-GH1/DMC-GF1 unit (marketed commodity: operates normal) etc. in accordance with the Micro Four Thirds
System and normal zoom lens H-FS014045 (marketed commodity) are necessary.
• Refer to the adjustment instruction in the adjustment software for details.
*2 NOTE: (When exchange the MAIN P.C.B.)
• Correspond by either the following when exchange the MAIN P.C.B. unavoidably by destruction and damage etc. of MAIN
P.C.B..
1. When it can turn on power, and the adjustment software can communicate with the camera body:
• Before replacing, proceed the FLASH-ROM data backup from the unit. After replacing, overwrite the FLASH-ROM data with
backup data from the unit, before proceeding the main body adjustment.
2. When it cannot turn on power, or the adjustment software cannot communicate with the camera body:
• The readjustment of mount box unit etc. are necessary.
• Refer to the adjustment instruction in the adjustment software for details.
• Refer to the adjustment instruction in the adjustment software for details.
*3 NOTE: (After exchange the mount box unit)
• Execute the resolution inspection by the comparison with the standard model (DMC-G1K etc.: operates normal).
• Refer to the adjustment instruction in the adjustment software for details.
• Refer to the adjustment instruction in the adjustment software for details.
*4
• Confirm self recording/playback motion picture of AVCHD mode by the LCD.
• Confirm it on the TV with HDMI socket when repair HDMI relation.
• Confirm it on the TV with HDMI socket when repair HDMI relation.
Replaced Part
Adjustment Item
Mount Box
Unit
(*3)
Main
P.C.B.
(*2)
Flash
P.C.B.
Power
P.C.B.
LCD U
Lens U/
L-Mount/
Rear
Frame
Camera
Body
Section
Body
Section
ISO sensitivity adjustment
(ISO)
(ISO)
O
O
-
-
-
-
High brightness coloration inspection
(SEN)
(SEN)
O
O
-
-
-
-
AWB adjustment
(WBL/WBM)
(WBL/WBM)
O
O
-
-
-
-
IMAGE SENSOR white scratch compensation
(WKI)
(WKI)
O
O
-
-
-
-
IMAGE SENSOR black scratch compensation
(BKI)
(BKI)
O
O
-
-
-
-
Mount Box Adjustment data writing
O
-
-
-
-
-
AVCHD function inspection
-
O(*4)
-
-
-
-
Defect
Part
Division/
Inspection
Part
Division/
Inspection
Resolution inspection
(*1)
(*1)
O
-
-
-
-
-
62
* There are no LCD adjustment model.
63
11 Maintenance
11.1. Notice in external cleaning
11.1.1.
ABOUT THE BODY
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit.
Also, remove the SD Memory card and lens unit.
11.1.1.1. DUST/DIRT ON THE OUTER CASING PART (S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
11.1.1.2. DUST/DIRT ON THE IMAGE SENSOR
1. Blow off the dust on the surface of the Image sensor with the Blower. (Refer to the following Figure.)
• Keep the Mount Facing down condition towards to floor when cleaning.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
2. Wipe off the dirt on the image sensor surface with Lens cleaning KIT(BK)(VFK1900BK).
64
11.1.2.
ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
11.1.2.2. DUST/DIRT ON THE LENS GLASSES
• Define the location of the dust/dirt first, whether it is outside
lens surface or not.
1. When it is outside surface of the lens:
• When the dust and/or dirt gets on the outer side sur-
face of the Lens glasses, order the following proce-
dures.
dures.
a. Blow off the dust on the Lens glass surface with
the Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with
Lens cleaning KIT(BK) (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
2. When it is inside of the lens:
• Refer to the “11.2. General description (Lens clean-
ing: Interchangeable Lens/H-H020)”, “11.3. General
description (Lens cleaning: Interchangeable Lens/H-
FS014045)” section of this service manual.
description (Lens cleaning: Interchangeable Lens/H-
FS014045)” section of this service manual.
11.2. General description (Lens cleaning: Interchangeable Lens/H-H020)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
Click on the first or last page to see other DMC-GF1CPP / DMC-GF1CEB / DMC-GF1CEC / DMC-GF1CEG / DMC-GF1CGC / DMC-GF1CGH / DMC-GF1CGK / DMC-GF1CGN / DMC-GF1KPP / DMC-GF1KEB / DMC-GF1KEC / DMC-GF1KEG / DMC-GF1KGC / DMC-GF1KGH / DMC-GF1KGK / DMC-GF1KGN / DMC-GF1PP / DMC-GF1EB / DMC-GF1EC / DMC-GF1EG / service manuals if exist.