Panasonic DMC-FX40EB / DMC-FX40EE / DMC-FX40EF / DMC-FX40EG / DMC-FX40EP / DMC-FX40SG / DMC-FX48P / DMC-FX48PC / DMC-FX48PU / DMC-FX48GC / DMC-FX48GD / DMC-FX48GH / DMC-FX48GJ / DMC-FX48GK / DMC-FX48GT Service Manual ▷ View online
25
8.3.4.
Removal of the Top Operation Unit
(Fig.D5)
8.3.5.
Removal of the Flash Top P.C.B.
(Fig.D6)
(Fig.D7)
26
8.3.6.
Removal of the Lens Unit
(Fig.D8)
8.3.7.
Removal of the Main P.C.B. and Sub
P.C.B.
P.C.B.
(Fig.D9)
27
8.3.8.
Removal of the Battery Case
(Fig.D10)
8.3.9.
Removal of the Jack Door
(Fig.D11)
8.3.10. Removal of the Battery Door Unit
(Fig.D12)
NOTE: (When Assembling)
Be sure to confirm the following points when assembling.
• The Screw is tightened enough.
• Assembling conditions are fine. (No distortion, no illegal-
• Assembling conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
28
8.4.
Disassembly Procedure for the
Lens
Lens
NOTE: When Disassembling and Assembling for the Lens
1. To minimize the possibility of the CCD being dirt, perform
disassemble and/or assemble under the condition of the
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
2. Take care that the dust and dirt are not entered into the
lens.
In case of the dust is putted on the lens, blow off them by
airbrush.
In case of the dust is putted on the lens, blow off them by
airbrush.
3. Do not touch the surface of lens.
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
shown to “Grease apply“ in the figure.
When the grease is applied, use a toothpick and apply
thinly.
When the grease is applied, use a toothpick and apply
thinly.
6. When repair the fixed frame, drive frame and direct
frame, must be unit exchange.
8.4.1.
Removal of the Zoom Motor Unit
and Lens FPC P.C.B. Unit
and Lens FPC P.C.B. Unit
1. Remove the 1 solder (A).
2. Remove the 1 solder (B).
3. Unscrew the 2 screws (A).
4. Unscrew the 1 screw (B).
5. Remove the 2 locks.
6. Remove the zoom motor unit to the indicated by arrow
2. Remove the 1 solder (B).
3. Unscrew the 2 screws (A).
4. Unscrew the 1 screw (B).
5. Remove the 2 locks.
6. Remove the zoom motor unit to the indicated by arrow
(1).
7. Remove the lens FPC P.C.B. unit to the indicated by
arrow (2).
Click on the first or last page to see other DMC-FX40EB / DMC-FX40EE / DMC-FX40EF / DMC-FX40EG / DMC-FX40EP / DMC-FX40SG / DMC-FX48P / DMC-FX48PC / DMC-FX48PU / DMC-FX48GC / DMC-FX48GD / DMC-FX48GH / DMC-FX48GJ / DMC-FX48GK / DMC-FX48GT service manuals if exist.