Panasonic DMC-FX10P / DMC-FX10PC / DMC-FX10PL / DMC-FX10EB / DMC-FX10EE / DMC-FX10EF / DMC-FX10EG / DMC-FX10EGM / DMC-FX10GC / DMC-FX10GD / DMC-FX10GK / DMC-FX10GN / DMC-FX10GT / DMC-FX10SG / DMC-FX12P / DMC-FX12PC / DMC-FX12PL / DMC-FX12EB / DMC-FX12EE / DMC-FX12E Service Manual ▷ View online
25
8.3.7.
Removal of the Lens Unit
Fig. D9
8.3.8.
Removal of the Sub P.C.B.
Fig. D10
8.3.9.
Removal of the Battery Case
Fig. D11
NOTE: (When Assembling)
Be sure to confirm the following points when assembling.
• The Screw is tightened enough.
• Assembling conditions are fine. (No distortion, no illegal-
• Assembling conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
26
8.4.
Disassembly Procedure for the
Lens
Lens
NOTE: When Disassembling and Assembling for the Lens
1. To minimize the possibility of the CCD being dirt, perform
disassemble and/or assemble under the condition of the
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6.
2. Take care that the dust and dirt are not entered into the
lens.
In case of the dust is putted on the lens, blow off them by
airbrush.
In case of the dust is putted on the lens, blow off them by
airbrush.
3. Do not touch the surface of lens.
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (VFK1829) to the point where is shown
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (VFK1829) to the point where is shown
to" Grease apply" in the figure.
When the grease is applied, use a toothpick and apply
thinly.
When the grease is applied, use a toothpick and apply
thinly.
8.4.1.
Zoom Motor Unit, Master Frange
Unit, Drive/Direct Frame Unit and
1st Lens Frame/2nd Lens Frame
Move Unit
Unit, Drive/Direct Frame Unit and
1st Lens Frame/2nd Lens Frame
Move Unit
1. Remove the cover to the indicated by arrow (A).
2. Unscrew the 2 screws (A).
3. Remove the zoom motor unit to the indicated by arrow.
4. Remove the 1 lock.
5. Unscrew the 1 screw (B).
2. Unscrew the 2 screws (A).
3. Remove the zoom motor unit to the indicated by arrow.
4. Remove the 1 lock.
5. Unscrew the 1 screw (B).
27
6. Slide the focus motor unit to the indicated by arrow (B).
7. Pull up the flex to exceed the convex part.
7. Pull up the flex to exceed the convex part.
8. Temporary screw the focus motor with screw (B).
9. Unscrew the 3 screws (C).
9. Unscrew the 3 screws (C).
10. Move the master frange unit to the indicated by arrow.
11. Turn the drive gear to the indicated by arrow fully.
28
12. Push the drive unit to the indicated by arrow from lens
side, and then remove the unit of drive/direct frame unit,
1st lens frame/2nd lens frame move unit from the fixed
frame unit.
1st lens frame/2nd lens frame move unit from the fixed
frame unit.
13. Push the 1st lens frame unit to the indicated by arrow
from lens side, and then remove the unit of 1st lens
frame/2nd lens frame move unit from the drive/direct
frame unit.
frame/2nd lens frame move unit from the drive/direct
frame unit.
8.4.2.
Removal of the Direct Frame
8.4.3.
Removal of the 2nd Lens Frame
Move Unit
Move Unit
Click on the first or last page to see other DMC-FX10P / DMC-FX10PC / DMC-FX10PL / DMC-FX10EB / DMC-FX10EE / DMC-FX10EF / DMC-FX10EG / DMC-FX10EGM / DMC-FX10GC / DMC-FX10GD / DMC-FX10GK / DMC-FX10GN / DMC-FX10GT / DMC-FX10SG / DMC-FX12P / DMC-FX12PC / DMC-FX12PL / DMC-FX12EB / DMC-FX12EE / DMC-FX12E service manuals if exist.