Panasonic DMC-FX07PP / DMC-FX07PL / DMC-FX07EB / DMC-FX07EE / DMC-FX07EF / DMC-FX07EG / DMC-FX07EGM / DMC-FX07GC / DMC-FX07GD / DMC-FX07GK / DMC-FX07GN / DMC-FX07GT / DMC-FX07SG Service Manual ▷ View online
29
8.6.
Removal of the CCD Unit
To prevent the CCD unit from catching the dust and dirt, do not
remove the CCD unit except for replacing.
remove the CCD unit except for replacing.
8.7.
The Applyment of Grease
Method
Method
The grease apply point of lens unit are as follows.
Apply grease additionally in the specified position if necessary.
Apply grease additionally in the specified position if necessary.
• Lead screw
- Grease: VFK1850 (Furoyl type)
- Amount of apply: 2 - 4 mg
- Amount of apply: 2 - 4 mg
• Guide pole
- Grease: VFK1829
- Amount of apply: 2 - 4 mg
- Amount of apply: 2 - 4 mg
30
9 Measurements and Adjustments
9.1.
Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-PAVC”.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-PAVC”.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
NOTE:
*There is no LCD adjustment in this model.
*There is no CCD Black scratch compensation adjustment (BKI) in this model.
*There is no CCD Black scratch compensation adjustment (BKI) in this model.
Replaced Part
Adjustment Item
Main P.C.B.
VENUS
(IC6001)
Flash-ROM
(IC6002)
Lens Part
(Excluding
CCD)
CCD Unit
Camera
Section
Section
OIS hall element adjustment
(OIS)
(OIS)
O
O
O
O
Back focus adjustment
(BF)
(BF)
O
O
O
O
Shutter adjustment
(SHT)
(SHT)
O
O
O
O
O
ISO sensitivity adjustment
(ISO)
(ISO)
O
O
O
O
O
AWB adjustment
High brightness coloration inspection
(WBL)
High brightness coloration inspection
(WBL)
O
O
O
O
O
CCD white scratch compensation
(WKI)
(WKI)
O
O
O
O
31
10 Maintenace
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash Top P.C.B. .................................................................... S-2
S2.1. Flash Top P.C.B. .................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Top Schematic Diagram .............................................. S-5
S4.3. AF Assist LED Schematic Diagram ....................................... S-6
S4.4. CCD Flex Schematic Diagram .............................................. S-6
S4.5. Lens Flex Schematic Diagram .............................................. S-7
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Top Schematic Diagram .............................................. S-5
S4.3. AF Assist LED Schematic Diagram ....................................... S-6
S4.4. CCD Flex Schematic Diagram .............................................. S-6
S4.5. Lens Flex Schematic Diagram .............................................. S-7
S5. Print Circuit Board .................................................................... S-8
S5.1. Flash Top P.C.B. .................................................................... S-8
S5.2. AF Assist LED P.C.B.. ........................................................... S-9
S5.3. CCD Flex P.C.B. .................................................................... S-9
S5.4. Lens Flex P.C.B. .................................................................. S-10
S5.1. Flash Top P.C.B. .................................................................... S-8
S5.2. AF Assist LED P.C.B.. ........................................................... S-9
S5.3. CCD Flex P.C.B. .................................................................... S-9
S5.4. Lens Flex P.C.B. .................................................................. S-10
S6. Replacement Parts List .......................................................... S-11
S7. Exploded View ....................................................................... S-17
S7.1. Frame and Casing Section.................................................. S-17
S7.2. Packing Parts and Accessories Section (1) ........................ S-18
S7.3. Packing Parts and Accessories Section (2) ........................ S-19
S7.1. Frame and Casing Section.................................................. S-17
S7.2. Packing Parts and Accessories Section (1) ........................ S-18
S7.3. Packing Parts and Accessories Section (2) ........................ S-19
Table of contents
Vol. 1
Colour
(S)...........Silver Type
(K)...........Black Type
(N)...........Gold Type (only EE/GC/GK/GT/SG)
(R)...........Red Type (only PP/EF/EG/EGM)
(P)...........Pink Type (only GC/GK/GN/GT/SG)
(A)...........Blue Type (only PP/EB/EE/EF/EG/EGM)
(K)...........Black Type
(N)...........Gold Type (only EE/GC/GK/GT/SG)
(R)...........Red Type (only PP/EF/EG/EGM)
(P)...........Pink Type (only GC/GK/GN/GT/SG)
(A)...........Blue Type (only PP/EB/EE/EF/EG/EGM)
Service Manual
Digital Camera
DSC0607021CE
Diagrams and Replacement
Parts List
DMC-FX07PP
DMC-FX07PL
DMC-FX07EB
DMC-FX07EE
DMC-FX07EF
DMC-FX07PL
DMC-FX07EB
DMC-FX07EE
DMC-FX07EF
DMC-FX07EG
DMC-FX07EGM
DMC-FX07GC
DMC-FX07GD
DMC-FX07GK
DMC-FX07EGM
DMC-FX07GC
DMC-FX07GD
DMC-FX07GK
DMC-FX07GN
DMC-FX07GT
DMC-FX07SG
DMC-FX07GT
DMC-FX07SG
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "
" mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other DMC-FX07PP / DMC-FX07PL / DMC-FX07EB / DMC-FX07EE / DMC-FX07EF / DMC-FX07EG / DMC-FX07EGM / DMC-FX07GC / DMC-FX07GD / DMC-FX07GK / DMC-FX07GN / DMC-FX07GT / DMC-FX07SG service manuals if exist.