Panasonic DMC-FS6P / DMC-FS6PC / DMC-FS6PR / DMC-FS6PU / DMC-FS6EB / DMC-FS6EE / DMC-FS6EF / DMC-FS6EG / DMC-FS6EP / DMC-FS6GC / DMC-FS6GJ / DMC-FS6GK / DMC-FS6GN / DMC-FS6GT Service Manual ▷ View online
33
8.6.
Removal of the CCD Unit
To prevent the CCD unit from catching the dust and dirt, do
not remove the CCD unit except for replacing.
not remove the CCD unit except for replacing.
8.7.
The Applyment of Grease
Method
Method
The grease apply point of lens unit are as follows.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
• Guide pole/Fasten groove of nut/Focus motor (lead screw)
- Grease: RFKZ0472
- Amount of apply: 2 - 4 mg
- Amount of apply: 2 - 4 mg
34
9 Measurements and Adjustments
9.1.
Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
*1: This adjustment is necessary, not only replacing CCD unit but also removing it from the lens unit.
NOTE:
*There is no LCD adjustment in this model.
Replaced Part
Adjustment Item
Main P.C.B.
VENUS
(IC6001)
Flash-ROM
(IC6002)
Lens Part
(Excluding
CCD)
CCD Unit
Camera
Section
Section
OIS hall element adjustment
(OIS)
(OIS)
O
O
O
O
-
Back focus adjustment
(BF)
(BF)
O
O
O
O
O
*1
Shutter adjustment
(SHT)
(SHT)
O
O
O
O
O
ISO sensitivity adjustment
(ISO)
(ISO)
O
O
O
O
O
AWB adjustment
High brightness coloration inspection
(WBL)
High brightness coloration inspection
(WBL)
O
O
O
O
O
CCD white scratch compensation
(WKI)
(WKI)
O
O
O
-
O
*1
CCD black scratch compensation
(BKI)
(BKI)
O
O
O
-
O
*1
Venus zoom inspection
(PZM)
(PZM)
O
O
O
-
-
Monitor linearity inspection
(MLN)
(MLN)
O
O
O
O
O
Colour reproduction inspection,
MIC inspection
(COL)
MIC inspection
(COL)
O
O
O
O
O
35
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash Top P.C.B. .................................................................... S-2
S2.1. Flash Top P.C.B. .................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Top Schematic Diagram .............................................. S-5
S4.3. Lens Flex Schematic Diagram .............................................. S-6
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Top Schematic Diagram .............................................. S-5
S4.3. Lens Flex Schematic Diagram .............................................. S-6
S5. Print Circuit Board .................................................................... S-7
S5.1. Flash Top P.C.B. .................................................................... S-7
S5.2. Lens Flex P.C.B. .................................................................... S-8
S5.1. Flash Top P.C.B. .................................................................... S-7
S5.2. Lens Flex P.C.B. .................................................................... S-8
S6. Replacement Parts List ............................................................ S-9
S7. Exploded View ....................................................................... S-13
S7.1. Frame and Casing Section.................................................. S-13
S7.2. Packing Parts and Accessories Section (1) ........................ S-14
S7.3. Packing Parts and Accessories Section (2) ........................ S-15
S7.1. Frame and Casing Section.................................................. S-13
S7.2. Packing Parts and Accessories Section (1) ........................ S-14
S7.3. Packing Parts and Accessories Section (2) ........................ S-15
Table of contents
Service Manual
DSC0902003CE
Diagrams and Replacement
Parts List
Vol. 1
(S)...........Silver Type (except PC/GT)
Colour
(K)...........Black Type (except GT)
(P)...........Pink Type (except EF/EP)
(P)...........Pink Type (except EF/EP)
(R)...........Red Type (except GC/GJ/GN/GT)
(A)...........Blue Type (except EF/GK/GN)
Model No.
DMC-FS6P
DMC-FS6PC
DMC-FS6PU
DMC-FS6PR
DMC-FS6EG
DMC-FS6EP
DMC-FS6EF
DMC-FS6P
DMC-FS6PC
DMC-FS6PU
DMC-FS6PR
DMC-FS6EG
DMC-FS6EP
DMC-FS6EF
DMC-FS6EB
DMC-FS6EE
DMC-FS6GC
DMC-FS6GJ
DMC-FS6GT
DMC-FS6GK
DMC-FS6GN
DMC-FS6EE
DMC-FS6GC
DMC-FS6GJ
DMC-FS6GT
DMC-FS6GK
DMC-FS6GN
Digital Camera
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other DMC-FS6P / DMC-FS6PC / DMC-FS6PR / DMC-FS6PU / DMC-FS6EB / DMC-FS6EE / DMC-FS6EF / DMC-FS6EG / DMC-FS6EP / DMC-FS6GC / DMC-FS6GJ / DMC-FS6GK / DMC-FS6GN / DMC-FS6GT service manuals if exist.