Panasonic DMC-F1PP / DMC-F1PM / DMC-F1E / DMC-F1B / DMC-F1A / DMC-F1EN / DMC-F1T / DMC-F1KR (serv.man2) Service Manual ▷ View online
2003
DMC-F1PP
DMC-F1PM
DMC-F1E
DMC-F1B
DMC-F1A
DMC-F1EN
DMC-F1T
DMC-F1KR
DMC-F1PM
DMC-F1E
DMC-F1B
DMC-F1A
DMC-F1EN
DMC-F1T
DMC-F1KR
Vol. 2
Colour
(S)...........Silver Type
(K)...........Black Type
(A)...........Blue Type (E/EN/KR only)
(R)...........Red Type (E/EN/KR only)
(D)...........Orange Type (EN/KR only)
Digital Camera
ORDER NO. DSC0301002C0
B26
1
INTRODUCTION
3
1.1.
INTRODUCTION
3
1.2.
ABOUT LEAD FREE SOLDER (PbF)
3
1.3.
HOW TO DEFINE THE MODEL SUFFIX (NTSC or PAL
model)
4
2
SAFETY PRECAUTIONS
6
2.1.
GENERAL GUIDELINES
6
2.2.
LEAKAGE CURRENT COLD CHECK
6
2.3.
LEAKAGE CURRENT HOT CHECK (See Figure 1.)
6
3
PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO
ELECTROSTATICALLY SENSITIVE (ES) DEVICES
7
4
HOW TO RECYCLE THE LITHIUM ION BATTERY(U.S. ONLY)
7
5
CAUTION FOR AC CORD (VJA0940 TYPE) (B only)
8
5.1.
INFORMATION FOR YOUR SAFETY
8
5.2.
CAUTION FOR AC MAINS LEAD
8
6
HOW TO REPLACE THE LITHIUM BATTERY
9
6.1.
REPLACEMENT PROCEDURE
9
7
SERVICE NOTES
11
7.1.
WHEN REPLACING THE MAIN C.B.A.
11
7.2.
SERVICE POSITION
11
7.3.
HOW TO DISCHARGE THE CAPACITOR ON MAIN
C.B.A.
12
7.4.
CLEANING LENS, OPTICAL VIEWFINDER AND LCD
PANEL
12
7.5.
HANDLING FOR THE MAIN C.B.A.
12
8
SCHEMATIC DIAGRAMS
13
8.1.
POWER BLOCK DIAGRAM
13
8.2.
SYSTEM CONTROL BLOCK DIAGRAM
14
8.3.
VIDEO/AUDIO PROCESS BLOCK DIAGRAM
15
8.4.
SENSOR BLOCK DIAGRAM
16
8.5.
LENS DRIVE BLOCK DIAGRAM
17
8.6.
MAIN SCHEMATIC DIAGRAM
18
9
I/O CHART
27
9.1.
IC1001 6CH SW REGULATOR
27
9.2.
IC3002 V-CCD DRIVE
27
9.3.
IC3003 CDS/AGC/AD
27
9.4.
IC3101 CCD IMAGE SENSOR
28
9.5.
IC4001 LCD COLOR DRIVER
28
9.6.
IC5001 AUDIO ANALOG
29
9.7.
IC6005 VENUS
29
9.8.
IC7001 LENS DRIVE
31
10 IC BLOCK DIAGRAM
33
11 CIRCUIT BOARD ASSEMBLIES
35
11.1. MAIN C.B.A.
35
12 REPLACEMENT PARTS LIST
39
12.1. ELECTRICAL REPLACEMENT PARTS LIST
39
CONTENTS
Page
Page
2
DMC-F1PP / DMC-F1PM / DMC-F1E / DMC-F1B / DMC-F1A / DMC-F1EN / DMC-F1T / DMC-F1KR
1 INTRODUCTION
1.1. INTRODUCTION
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
1.2. ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB.
Caution:
·
Pb free solder has a higher melting point than standard solder, Typically the melting point is 50-70°F (30-40°C) higher.
Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700±20°F
(370±10°C)
(370±10°C)
·
Pb free solder will tend to splash when heated too high (about 1100°F/600°C).
When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the
soldering points with the Pb free solder until it melts enough.
soldering points with the Pb free solder until it melts enough.
3
DMC-F1PP / DMC-F1PM / DMC-F1E / DMC-F1B / DMC-F1A / DMC-F1EN / DMC-F1T / DMC-F1KR
1.3. HOW TO DEFINE THE MODEL SUFFIX (NTSC or PAL model)
There are four kinds of DMC-F1, regardless the colours.
·
DMC-F1S
·
DMC-F1PP
·
DMC-F1E/B/A/EN/ED/T
·
DMC-F1PM/KR
(DMC-F1S is exclusively Japan domestic model and ONLY this model has “SERIAL” terminal just below the USB terminal.)
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main C.B.A.
1.3.1. Defining methods:
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN C.B.A., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “CS-Web from AVC” web-site in “TSN system”.
4
DMC-F1PP / DMC-F1PM / DMC-F1E / DMC-F1B / DMC-F1A / DMC-F1EN / DMC-F1T / DMC-F1KR