Panasonic WV-CP460 / WV-CP464 Service Manual ▷ View online
ORDER NO. AVS0005261C8
C
2 0 0 0 M a t s u s h i t a C o m m u n i c a t i o n I n d u s t r i a l C o . , L t d .
A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
Colour CCTV Cameras
WV-CP460/WV-CP464
SPECIFICATIONS
Pick-up Device:
753 (H) x 582 (V) pixels, Interline Transfer CCD
Scanning Area:
4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)
Scanning:
625 lines/50 fields/25 frames
Horizontal:
15.625 kHz
Vertical:
50 Hz
Synchronization:
Internal, Line-locked, External (VS/VBS) or
Multiplexed Vertical Drive (VD2) selectable
Multiplexed Vertical Drive (VD2) selectable
Video Output:
1.0 V[p-p] PAL composite 75
Ω
/BNC connector
Horizontal Resolution:
480 lines
Signal-to-Noise Ratio:
50 dB (AGC OFF, weight ON)
Dynamic Range:
48 dB
Minimum Illumination:
0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx (0.08 footcandle) at F1.4]
Gain Control:
AGC ON or OFF (SET UP MENU) selectable
White Balance:
ATW or AWC (SET UP MENU) selectable
Aperture:
Set Variable (SET UP MENU)
Electronic Light Control:
Equivalent to continuous variable shutter speeds between 1/50 s and 1/10 000 s
Super Dynamic
2
:
ON or OFF (SET UP MENU) selectable
Electronic Shutter Speed:
1/50 (OFF), 1/120, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable
1/4 000, 1/10 000 s selectable
Lens Mount:
C-mount or CS-mount selectable
ALC Lens:
DC or Video selectable
Ambient Operating Temperature:
–10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity:
Less than 90 %
WV-CP460:
220-240 V AC 50 Hz, 5.1 W
Power Consumption:
WV-CP464:
24 V AC 50 Hz, 4.8 W
12 V DC, 480 mA
12 V DC, 480 mA
Dimensions (without lens):
74 (W) x 55 (H) x 123 (D) mm
[2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)]
[2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)]
Weights (without lens):
WV-CP460:
0.41 kg (0.9 lbs.) (without power cord)
WV-CP464:
0.4 kg (0.9 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
Specifications are subject to change without notice.
(Lens: Option)
WV-CP460 Series
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
!
WARNING
STANDARD ACCESSORIES
Body Cap................................................................................1 pc.
ALC Lens Connector (YFE4191J100) ....................................1 pc.
AC Power Cord (only WV-CP460)..........................................1 pc.
ALC Lens Connector (YFE4191J100) ....................................1 pc.
AC Power Cord (only WV-CP460)..........................................1 pc.
OPTIONAL ACCESSORIES
Lenses :
WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B,
WV-LA210C3, WV-LA408C3 WV-LA908C3,
WV-LZ61/10, WV-LZ61/15, WV-LZ62/2, WV-
LZ62/8, WV-LF4R5C3A, WV-LF9C3A
WV-LA210C3, WV-LA408C3 WV-LA908C3,
WV-LZ61/10, WV-LZ61/15, WV-LZ62/2, WV-
LZ62/8, WV-LF4R5C3A, WV-LF9C3A
CONTENTS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS............................................................................... 1
ADJUSTMENT PROCEDURE ................................................................................................................................. 2
LOCATION OF TEST POINTS AND ADJUSTING CONTROLS........................................................................... 11
WIRING DIAGRAM ................................................................................................................................................ 12
SCHEMATIC DIAGRAM
SENSOR BOARD .............................................................................................................................................. 13
MAIN BOARD..................................................................................................................................................... 15
I/F BOARD ......................................................................................................................................................... 16
CONDUCTOR VIEW
SENSOR BOARD .............................................................................................................................................. 13
MAIN BOARD..................................................................................................................................................... 14
I/F BOARD ......................................................................................................................................................... 16
EXPLODED VIEW
WV-CP460 ......................................................................................................................................................... 17
WV-CP464 ......................................................................................................................................................... 18
REPLACEMENT PARTS LIST ............................................................................................................................. 19
<WV-CP460>
<WV-CP464>
q
e
w
r
t
y
o
u
!0
!1
i
!2
!3
!2
!5
!3
!4
Super
Dynamic
WV-
CP460
Hi-Z G/L 75
Ω
VIDEO OUT
220-240 V ~ 50Hz
GEN-LOCK
AC 24V
IN
DC 12V
IN
1
2
VIDEO OUT
GND
GEN-LOCK
WV-CP460 Series
– 1 –
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Slide the panel to the left until it locks.
q
Auto Iris Lens Connector
This connector is used to connect the auto iris lens with a
4-pin male connector supplied as a standard accessory
(Part No. YFE4191J100).
This connector is used to connect the auto iris lens with a
4-pin male connector supplied as a standard accessory
(Part No. YFE4191J100).
w
Focus-Fixing Screw
e
Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture
focus. Rotate this ring clockwise for a C-mount lens or
counterclockwise for a CS-mount lens.
This ring is used to adjust the back focal length or picture
focus. Rotate this ring clockwise for a C-mount lens or
counterclockwise for a CS-mount lens.
r
Lens (Option)
t
Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting
bracket.
This hole is used to mount the camera onto a mounting
bracket.
y
Down Button (
)
This button is used to move the cursor downward. It is
also used to select items in the CAM SET UP menu.
also used to select items in the CAM SET UP menu.
u
Left Button (
)
This button is used to move the cursor to the left. It also
selects the mode and can be used to adjust some levels.
selects the mode and can be used to adjust some levels.
i
Up Button (
)
This button is used to move the cursor upward. It is also
used to select items in the CAM SET UP menu.
used to select items in the CAM SET UP menu.
o
Right Button (
)
This button is used to move the cursor to the right. It also
selects the mode and can be used to adjust some levels.
selects the mode and can be used to adjust some levels.
Caution:
• Connect to 12 V DC (10.8 V-16 V) or 24 V AC (19.5 V-
28 V) class 2 power supply only. Make sure to connect
the grounding lead to the GND terminal when the
power is supplied from a 24 V AC power source.
the grounding lead to the GND terminal when the
power is supplied from a 24 V AC power source.
!0
Set Button (
)
This button is used to activate an item selected in the CAM
SET UP menu.
SET UP menu.
!1
Gen-lock Termination Switch (Hi-Z, G/L 75
Ω
)
Set this switch to Hi-Z when a gen-lock video input signal is
looped through. In all other cases, set this switch to 75
looped through. In all other cases, set this switch to 75
Ω
.
!2
Gen-lock Input Connector (GEN-LOCK)
This connector is used to connect an external system for
synchronization.
This connector is used to connect an external system for
synchronization.
!3
Video Output Connector (VIDEO OUT)
This connector is used to connect the VIDEO IN connector
of the monitor.
This connector is used to connect the VIDEO IN connector
of the monitor.
!4
AC Inlet Socket
This socket is used to connect the power cord (supplied as
a standard accessory).
This socket is used to connect the power cord (supplied as
a standard accessory).
!5
AC/DC Compatible Input Terminal
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V AC
power supply cord.
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V AC
power supply cord.
ADJUSTMENT PROCEDURE
1. Test Equipment Required
The following test equipment are required for adjustment
of the Colour CCTV Camera WV-CP460 and WV-CP464.
Oscilloscope
Frequency Counter
Waveform Monitor
Vectorscope
Underscanned Colour Video Monitor
Video Signal Generator
12 V DC Power Supply Unit
Personal Computer (IBM PC/AT type or equivalent)
Standard Straight RS-232C Cable
ALC Lens (WV-LA9C3A, WV-LA9C3B or equivalent)
Lux Meter
Lighting (275 footcandles (2,750 ± 150 lux), Colour
Temperature 5,100 ± 100 K)
Colour Temperature Conversion Filters
(KENKO: W12, C4 or equivalent)
Radiation Chart
Logarithmic Gray Scale Chart.
(Part Number:YWV2310RB99)
Extension Cable as shown in Fig. 1-1.
(Part Number: YWV0EA1171AN)
of the Colour CCTV Camera WV-CP460 and WV-CP464.
Oscilloscope
Frequency Counter
Waveform Monitor
Vectorscope
Underscanned Colour Video Monitor
Video Signal Generator
12 V DC Power Supply Unit
Personal Computer (IBM PC/AT type or equivalent)
Standard Straight RS-232C Cable
ALC Lens (WV-LA9C3A, WV-LA9C3B or equivalent)
Lux Meter
Lighting (275 footcandles (2,750 ± 150 lux), Colour
Temperature 5,100 ± 100 K)
Colour Temperature Conversion Filters
(KENKO: W12, C4 or equivalent)
Radiation Chart
Logarithmic Gray Scale Chart.
(Part Number:YWV2310RB99)
Extension Cable as shown in Fig. 1-1.
(Part Number: YWV0EA1171AN)
Make a conversion cable as follows.
Fig. 1-2
Remote Electric Variable Resistor (E. V. R.) kit as shown in
Fig. 1-2. (Part Number: YWV0EA1174AN)
Fig. 1-2. (Part Number: YWV0EA1174AN)
Fig. 1-3
13
12
11
10
9
8
7
6
5
4
3
2
1
26
25
24
23
22
21
20
19
18
17
16
15
14
GND
T (B)
R (B)
To
Remote
E. V. R.
Kit
Remote
E. V. R.
Kit
To PC
Via RS-232C
Cable
Via RS-232C
Cable
2. Disassembling Procedure for
Adjustment
Referring to Fig. 2-1, remove two screws that secure the
Mount Adaptor and remove the Mount Adaptor.
Mount Adaptor and remove the Mount Adaptor.
Referring to Fig. 2-2, remove two screws that secure the
Main Cover and remove the Main Cover.
Main Cover and remove the Main Cover.
Remove two screws
Mount Adaptor
Fig. 2-1
Fig. 2-2
Remove two screws
Main Cover
– 2 –
WV-CP460 Series
Fig. 1-1
To
Main Board
CN404
Main Board
CN404
To
Power Board
Unit CN101
Power Board
Unit CN101
CN3
CN2