Panasonic BL-C10CE / BL-C10E Service Manual ▷ View online
2004 Panasonic Communications
BL-C10CE
BL-C10E
(for Europe, Asia, Oceania, Middle Near East, Russia,
Africa and Latin America)
Network Camera
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear, please read and follow the special instructions described in this manual on the use of PbF and how
it might be permissible to use Pb solder during service and repair work.
it might be permissible to use Pb solder during service and repair work.
ORDER NO. KMS0410015C8
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
3
1.1.
SUGGESTED PbF SOLDER
3
1.2.
HOW TO RECOGNIZE THAT Pb FREE SOLDER IS
USED
4
2 FOR SERVICE TECHNICIANS
6
3 CAUTION
7
3.1.
SAFETY PRECAUTIONS
7
3.2.
BATTERY CAUTION
7
3.3.
TRADEMARKS
8
3.4.
INSULATION RESISTANCE TEST
8
3.5.
POWER CAUTION
9
3.6.
PRECAUTIONS FOR USERS IN THE UNITED KINGDOM
9
3.7.
CLEANING
11
4 SPECIFICATIONS
12
4.1.
ABOUT PYROELECTRIC INFRARED SENSOR
13
4.2.
COLOR NIGHT VIEW MODE
14
5 MAIN FEATURES
15
6 PARTS LOCATIONS
16
6.1.
FRONT VIEW
16
6.2.
BOTTOM VIEW
17
6.3.
REAR VIEW
17
7 CONNECTING YOUR NETWORK CAMERA
18
7.1.
PREPARATION
18
7.2.
CONNECT THE CAMERA TO YOUR ROUTER
19
7.3.
TURN THE CAMERA ON
19
7.4.
SETUP THE CAMERA
20
8 DISASSEMBLY INSTRUCTIONS
23
8.1.
HOW TO REMOVE MAIN BOARD AND I/O BOARD 23
8.2.
HOW TO REMOVE SUB BOARD
25
8.3.
HOW TO REMOVE EYE BLOCK
27
9 THE CAUTIONS AT THE TIME OF ASSEMBLY
29
9.1.
SUB FLAT CABLE INSERTIION INSTRUCTION
29
9.2.
ASSEMBLING INSTRUCTION OF WASHERS
30
9.3.
ASSEMBLING INSTRUCTION OF EYE BLOCK
31
9.4.
BOARD TAPE INSTALLATION INSTRUCTION
32
9.5.
SHEET INSTALLATION INSTRUCTION
33
9.6.
CABLE INSTALLATION INSTRUCTION
34
10 TROUBLE SHOUTING
35
10.1. STARTING UP OPERATION
35
10.2. LED CIRCUIT CHECK
36
10.3. LAN BLOCK CHECK
37
10.4. CAMERA BLOCK CHECK
40
10.5. POWER SUPPLY BLOCK CHECK
42
10.6. OTHER OPERATION CHECK
44
10.7. PYROELECTRIC INFRARED SENSOR CHECK
45
10.8. THE INSPECTION AFTER THE REPAIR
46
10.9. CONFIRMING THE STATUS
46
10.10. UPDATE FIRMWARE
47
11 THE WAY OF THE INITIALIZE
48
11.1. FACTORY DEFAULT RESET BUTTON
48
11.2. RESETTING THE CAMERA TO FACTORY DEFAULT 48
12 NETWORK CAMERA BL-C10 BLOCK DIAGRAM
49
13 CIRCUIT DESCRIPTION
50
13.1. MAIN BOARD
50
14 IC DATA
58
14.1. IC2
58
14.2. IC51, 52
58
14.3. IC101
59
14.4. IC102
61
14.5. IC103
62
14.6. IC104
63
14.7. IC105
63
14.8. IC201
64
14.9. IC402
66
14.10. IC701
67
14.11. IC801
68
14.12. IC802
68
14.13. IC803
69
14.14. IC804
69
15 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES
70
16 HOW TO REPLACE A FLAT PACKAGE IC
71
16.1. PREPARATION
71
16.2. PROCEDURE
71
16.3. REMOVING SOLDER FROM BETWEEN PINS
71
17 CABINET AND ELECTRICAL PARTS LOCATION
72
18 ACCESSORIES AND PACKING MATERIALS
73
19 REPLACEMENT PARTS LIST
74
19.1. CABINET AND ELECTRICAL PARTS
74
19.2. ACCESSORIES AND PACKING MATERIALS
74
19.3. MAIN BOARD PARTS
74
19.4. I/O BOARD PARTS
76
19.5. SUB BOARD PARTS
77
19.6. GREASE
77
20 FOR THE SCHEMATIC DIAGRAM
78
21 SCHEMATIC DIAGRAM
79
21.1. WAVEFORM
87
22 CIRCUIT BOARD
90
22.1. MAIN BOARD (COMPONENT VIEW)
90
22.2. MAIN BOARD (BOTTOM VIEW)
91
22.3. I/O BOARD (COMPONENT VIEW)
92
22.4. I/O BOARD (BOTTOM VIEW)
93
22.5. SUB BOARD (COMPONENT VIEW)
94
22.6. SUB BOARD (BOTTOM VIEW)
94
22.7. LENS BOARD (COMPONENT VIEW)
95
22.8. LENS BOARD (BOTTOM VIEW)
95
CONTENTS
Page
Page
2
BL-C10CE / BL-C10E
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that
contains lead.
contains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).
Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
Caution
· PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with
temperature control and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high temperature soldering iron, please
be careful not to heat too long.
be careful not to heat too long.
· PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).
· If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible
· If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible
and be sure that any remaining is melted prior to applying the Pb solder.
· When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See figure, below).
1.1. SUGGESTED PbF SOLDER
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the
manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials. The following lead free (PbF) solder wire gauge are recommended for service of this product: 0.3mm, 0.6mm and
1.0mm.
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the
manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials. The following lead free (PbF) solder wire gauge are recommended for service of this product: 0.3mm, 0.6mm and
1.0mm.
3
BL-C10CE / BL-C10E
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED
MAIN BOARD
4
BL-C10CE / BL-C10E