Panasonic CQ-EH1180L / CQ-EH1181L Service Manual ▷ View online
5.1. Power and Volume Controls
5.1.1. Power
∙
Press PWR knob (1) to switch on the power.
∙
Perss PWR knob (1) again to switch off the power.
5.1.2. Volume
∙
Turn VOL knob (1) to the right or left to increase or
decrease the volume.
decrease the volume.
5.2. Tone Controls
5.2.1. Changing Audio Modes
∙
Press MODE knob (2) to change the audio mode as follows.
BASS
→
TREB
→
FADE
→
BAL
→
.... BASS ...
5.2.2. Bass
1. Press MODE knob (2) to select the bass mode.
2. Turn knob (2) to the right or left to increase or decrease the
low tones.
5.2.3. Treble
1. Press MODE knob (2) to select the treble mode.
2. Turn knob (2) to the right or left to increase or decrease the
high tones.
5.2.4. Fader
1. Press MODE knob (2) to select the fader mode.
2. Turn knob (2) to the right or left to shift the sound volume to
the front or rear speakers.
5.2.5. Balance
1. Press MODE knob (2) to select the balance mode.
2. Turn knob (2) to the right or left to shift the sound volume to
the right or left speakers.
5.3. Radio Controls
5.3.1. Selecting a Band
∙
Press AM button (6) to select the AM band.
∙
Press FM button (5) to select the FM band as follows.
FM1
→
FM2
→
... FM1 ...
5.3.2. Manual Tuning
∙
Turn TUNE knob (2) to the right to move to a higher
frequency by one step.
frequency by one step.
∙
Turn TUNE knob (2) to the left to move to a lower frequency
by one step.
by one step.
AM
FM
One Step
9kHz
50kHz
∙
Press and hold button (3) or (4) more than 0.5 seconds to
move to a higher or lower frequency rapidly.
move to a higher or lower frequency rapidly.
5.3.3. Seek Tuning
1. When SEEK button (3) is pressed less than 0.5 seconds,
the seek operation in the screen up direction is made.
2. The play stops when there is a station and this state is kept.
3. When SEEK button (4) is pressed less than 0.5 seconds,
the seek operation in the screen down direction is made.
4. The play stops when there is a station and this state is kept.
5.3.4. Scan Tuning
∙
Press SCAN button (10), then the frequency becomes
continuously higher by one step.
continuously higher by one step.
∙
When receiving a station, scanning operation pauses
automatically for approx. 5 seconds, and then start
scanning for next station again.
automatically for approx. 5 seconds, and then start
scanning for next station again.
5.3.5. Auto Station Memory
∙
When A.SEL button (11) press, the 6 strongest available
stations will be automaticaly set in memory on preset
buttons 1 through 6.
stations will be automaticaly set in memory on preset
buttons 1 through 6.
5.3.6. Presset Station Setting
FM1, FM2 and AM can save maximum 6 stations each.
∙
Press and hold one of the preset button 1 to 6 for more than
2 seconds to save a disired station.
2 seconds to save a disired station.
∙
Press and hold any of the button 1 to 6 for less than 2
seconds to tune in the station preset.
seconds to tune in the station preset.
M1
M2
M3
M4
M5
M6
AM
531
603
999
1404
1602
1602
FM1
87.5
87.9
90.1
98.1
106.1
108.0
FM2
87.5
87.5
87.5
87.5
87.5
87.5
(Unit : AM / kHz, FM / MHz)
5 OPERATION OF CONTROLS
5
HONDA / CQ-EH1180L / CQ-EH1181L
5.4. Tape Controls
5.4.1. Selecting a Tape Mode
∙
Press TAPE button (8) , if a cassette is loaded, then the
mode changes to the tape player mode.
mode changes to the tape player mode.
5.4.2. Fast Forward and Rewind
∙
Press FF button (9)-4 to fast forward the tape.
∙
Press REW button (9)-3 to rewind the tape.
5.4.3. Play Mode
∙
Press PLAY button (9)-1 to play the tape.
5.4.4. Changing Sides
∙
Press PROG button (9)-2 to change to the program on the
other side of the tape.
other side of the tape.
5.4.5. APC Operation
∙
If APC FF button (3) press, the cassette player fast forward
to the beginning of the next music.
to the beginning of the next music.
∙
If APC REW button (4) press, the cassette player rewind to
the beginning of the current music.
the beginning of the current music.
5.4.6. Repeat Play
∙
Press RPT button (10) to repeat the same music.
5.4.7. Dolby Noise Reduction
∙
Press "Dolby" button (9)-5 to set the Dolby B NR mode.
5.5. CD Changer Controls
5.5.1. Selecting a CD Changer Mode
∙
Press CD button (7), then the mode changes to the CD
changer mode.
changer mode.
5.5.2. Loading Discs
∙
Press LOAD button (12) less than 1.5 secondes to load a
disc.
disc.
∙
Press LOAD button (12) more than 1.5 secondes to load all
the disc.
the disc.
5.5.3. Ejecting Discs
∙
Press button (14) less than 1.5 secondes to eject a disc.
∙
Press button (14) more than 1.5 secondes to eject all the
disc.
disc.
5.5.4. Selecting a Disc
∙
Press one of the preset button 1 to 6 to select a disired disc.
5.5.5. Selecting a Track
∙
Press and hold the button (3) for less than 0.5 seconds to
go to the next track.
go to the next track.
∙
Press and hold the button (4) for less than 0.5 seconds to
play from the beginning of the track. Press twice to play the
previous track.
play from the beginning of the track. Press twice to play the
previous track.
5.5.6. Fast Forward and Revers
∙
Press and hold the button (3) more than 0.5 seconds to fast
forward a track.
forward a track.
∙
Press and hold the button (4) more than 0.5 seconds to
reverse through a track.
reverse through a track.
5.5.7. Repeating a Track
∙
Press RPT button (10) to repeat the current selection.
5.5.8. Random Selection
∙
Press RND button (11). A random selection of music is
played from all available tracks on the current disc.
played from all available tracks on the current disc.
5.6. Anti-Theft
5.6.1. Waiting for an Entry of Anti-Theft
Code
1. "CODE" display is made when the unit for preventing thefts
is mounted in the equipment to wait for an entry of anti-theft
code.
code.
2. "CODE" is displayed when the BATTERY + ceases to be
supplied, which is similar to a case where the anti-theft unit
has been removed from the equipment.
has been removed from the equipment.
5.6.2. An Entry of Anti-theft Code
∙
To enter the anti-theft code, use preset buttons P1 through
P6 ((9)-1 ~ (9)-6).
P6 ((9)-1 ~ (9)-6).
5.6.3. When the Entered Code Coincides
1. A "beep" is output.
2. The equipment is placed in the radio mode of operation.
5.6.4. When the Entered Code Does Not
Coincide
1. A "beep" is output for three times.
2. The equipment is put in a anti-theft code entry waiting state
as mentioned in 5.6.1-1) above.
6
HONDA / CQ-EH1180L / CQ-EH1181L
6 WIRING CONNECTIONS
7
HONDA / CQ-EH1180L / CQ-EH1181L
7 BLOCK DIAGRAM
7.1. Main,Display,Tape Block
8
HONDA / CQ-EH1180L / CQ-EH1181L
Click on the first or last page to see other CQ-EH1180L / CQ-EH1181L service manuals if exist.